Bedienungsanleitung Dirt Devil M3220 (Seite 15 von 50) (Holländisch, Italienisch, Spanisch, Türkisch)

500146

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

5 Maintenance

5.3 Cleaning the exhaust filter

 Check the exhaust filter every time you clean the motor protection filter

Chapter 5.2, "Cleaning dust container and motor protection filter" and

clean it if it is dirty.

1. Switch off the appliance, Chapter 4.3, "Switching off".

2. Push the release catch of the exhaust filter cover down (Fig. 12/A) and

open out the exhaust filter cover.

3. Remove the exhaust filter (Fig. 12/B).

4. Hold the exhaust filter over a dustbin.

5. Remove any residual dust by tapping. If the exhaust filter is still dirty,

thoroughly rinse it by hand until all dirt is gone.

6. If the exhaust filter is damaged, replace it (Chapter 5.4, "Spare parts

and accessories").

7. Now, put the exhaust filter holder with the freshly fitted filter back into

its bracket (Fig. 13/A).

8. Attach the exhaust filter cover at the bottom side first (Fig. 13/B) before

folding it up firmly. You will feel and hear it snap into place.

5.4 Spare parts and accessories

If you require accessories and spare parts:

Contact: Page 48, "International Service"

5.5 Before you send in the appliance

Before contacting or even sending the appliance to us, use the following ta-

ble to check whether you can correct the problem yourself.

ATTENTION:

The filter is washable, but it may not be cleaned in dishwashers or wash-

ing machines. Also, do not use detergents or brushes with hard bristles

to clean them. Let the filter dry for approx. 24 hours at room temperature

after washing it. Only put it back in place when it is completely dry.

ATTENTION:

Only use original spare parts from the scope of delivery or those that you

have purchased by reordering.

Item number Description

2818001 Motor protection filter set consisting of: 1 foam plastic filter

element (round) + 1 filter holder = 1 dual motor protection

filter; 1 small motor protection filter

2818002 1 exhaust filter

M203-5 1 parquet brush

M209 1 turbo brush

M219 1 mini turbo brush

M232 1 long flexible crevice nozzle

WARNING:

Danger of injury! Never use a defective appliance! Always switch off the

appliance and disconnect it from the mains before starting troubleshoot-

ing Chapter 4.3, "Switching off".

Problem Solution

Cleaning in-

dicator

(Fig. 1/6)

lights up or

cleaning re-

sults are not

satisfactory.

The dust container is full.

Empty the dust container, Chapter 5.1, "Emptying the

dust container".

The filters are dirty.

Clean the respective filter Chapter 5.2, "Cleaning dust

container and motor protection filter" or Chapter 5.3,

"Cleaning the exhaust filter".

Nozzle, telescopic tube or suction hose is blocked.

Remove the obstacle. If necessary, use a long wooden

stick (e.g. a broomstick) to do this.

The vacuum

cleaner

stops sud-

denly.

Overheating protection has tripped (possibly because you

ignored the lit cleaning indicator for too long).

Switch the appliance off and pull the plug out of the socket.

Eliminate the cause of overheating (e.g. Chapter 5.2,

"Cleaning dust container and motor protection filter"). Wait

for about 45 minutes. After the appliance has cooled off,

you may switch it on again.

The results

are unsatis-

factory in

spite of the

appliance

working cor-

rectly

(cleaning

indicator

(Fig. 1/6)

does not

light up).

The bypass vent (Fig. 1/20) is open.

Close the bypass vent (Fig. 1/20).

The attached nozzle is unsuitable.

Change the nozzle, Chapter 3.2, "Selecting the proper

nozzle".

The position of the ‘carpet/hard floor’ selector (Fig. 1/27) is

unsuitable.

Set the "carpet/hard floor" selector (Fig. 1/27) to the cor-

rect position for the type of floor, Chapter 4.2, "Vacuum

cleaning", step 4.

When vacu-

uming with

the long,

flexible crev-

ice nozzle,

there is sud-

denly a high-

pitched

whistling

and the suc-

tion power

drops con-

siderably.

The pressure in the vacuum cleaner became too low and

caused the safety valve to trigger.

Open the bypass vent until the valve no longer triggers.

Problem Solution

M3220.book Seite 15 Montag, 4. Juni 2012 3:15 15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dirt Devil M3220 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dirt Devil M3220

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info