Bedienungsanleitung Dirt Devil Vito Plus M2012-2 (Seite 15 von 24) (Deutsch, Englisch, Französisch)

500173

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

5 Maintenance

5.3 Cleaning the hygienic exhaust filter

1. Switch off the appliance, Zchapter 4.3, „Switching off“.

2. Push the release catch of the exhaust filter cover (Fig. 13/A) and lift off

the exhaust filter cover.

3. Pull the hygienic exhaust filter up out of its holder (Fig. 13/B) and tap

the dirt from it over a dust bin.

4. Should this be insufficient, remove the dirt from the filter with a soft

brush, e.g. the furniture brush supplied with the appliance (Fig. 14/A).

5. If such dry cleaning is insufficient, thoroughly rinse the filter by hand in

running clear cold or hand-warm water.

6. If the filter is damaged or deformed, replace it (ordering information

Zchapter 5.4, „Spare parts and accessories“).

7. Place the clean/new hygienic exhaust filter back into its fitting (Fig. 13/

B).

8. Then fit the exhaust filter cover on the rear side first and then push it

down on the front side (Fig. 14/B).

5.4 Spare parts and accessories

 Ordering address: Zpage 48, „International Service“

 Further information is available at: Z www.dirtdevil.de

5.5 Recommendation

We recommend:

>> Swirl

£

Y12 dust filter bags with MicroPor

filtration <<

Swirl

, MicroPor

and "Y12" are registered trademarks of a company of

the Melitta Group and are used with their permission.

5.6 Before you send in the appliance

Before contacting your authorised Royal dealer, Royal service partner or

appliance market or sending in the appliance, first follow the procedure in

the following table to check if you can solve the problem yourself.

ATTENTION:

The filters are washable, but not suitable for cleaning in washing

machines or dishwashers. Do not use chemical cleansers to clean the

filter. Leave the filters to dry after cleaning them with water

(approx. 24 hours at room temperature). Only put them back into the

appliance when they are completely dry.

ATTENTION:

Only use original spare parts from the scope of delivery or those that you

have acquired by reordering.

Item number Description

7075022 Set of 5 dust filter bags and 1 motor protection filter

7075002 1 hygienic exhaust filter

M232 1 long flexible crevice nozzle

M203-4 1 parquet brush

M208-8 1 turbo brush

WARNING:

Danger of injury! Never use a defective appliance! Always switch off the

appliance and disconnect it from the mains before starting troubleshoot-

ing Zchapter 4.3, „Switching off“.

Problem Possible cause / solution

Filter bag

change indicator

appears in the

display window.

The dust filter bag is full.

Change the dust filter bag Zchapter 5.1, „Changing

the dust filter bag“.

Nozzle, telescopic tube or suction hose are blocked.

Remove the obstacle. If necessary, use a long wooden

stick (e.g. a broomstick) to do this.

The filters are dirty.

Clean the respective filter Zchapter 5.2, „Cleaning the

motor protection filter“ or Zchapter 5.3, „Cleaning the

hygienic exhaust filter“.

The vacuum

cleaner stops

suddenly.

The overheating protection has tripped (possibly due

to blocked suction channels, filters, or similar). Switch

the appliance off and pull the plug out of the socket.

Remove the cause of overheating (e.g. by disassem-

bling telescopic tube and suction hose and removing

the obstacle and/or cleaning filters). Wait for about

45 minutes. After the appliance has cooled off, you

may switch it on again.

The cleaning re-

sults are unsat-

isfactory in spite

of the appliance

working correct-

ly.

The bypass vent (Fig. 1/15) is open.

Close the bypass vent (Fig. 1/15).

The attached nozzle is unsuitable. Change the nozzle,

Zchapter 3.2, „Selecting the proper nozzle“

Position of the suction power control (Fig. 1/17) is not

suitable for the floor. Adjust the suction power control

(Fig. 1/17), Zchapter 4.2, „Vacuum cleaning“, step 4.

The position of the "carpet/hard floor" selector (Fig. 1/

2) is unsuitable for the floor. Set the "carpet/hard floor"

selector (Fig. 1/2) to the correct position, Zchapter

4.2, „Vacuum cleaning“, step 5.

The dust filter bag is full. Change the dust filter bag

Zchapter 5.1, „Changing the dust filter bag“.

The filters are dirty. Clean the respective filter

Zchapter 5.2, „Cleaning the motor protection filter“ or

Zchapter 5.3, „Cleaning the hygienic exhaust filter“.

Nozzle, telescopic tube or suction hose are blocked.

Remove the obstacle. If necessary, use a long wooden

stick (e.g. a broomstick) to do this.

Dust compart-

ment cover can-

not be closed

Dust filter bag has not been inserted or has been in-

serted incorrectly. Insert the dust filter bag correctly,

Zchapter 5.1, „Changing the dust filter bag“.

NOTE:

If you cannot solve the problem following these instructions, contact the

Royal Appliance customer service (Zpage 48, „International Service“).

Problem Possible cause / solution

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dirt Devil Vito Plus M2012-2 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info