Bedienungsanleitung DITEC BOX3EH (Seite 12 von 32) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

749190

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

BOX - IP1529

1. DATI TECNICI

BOX30 BOX40 BOX3SH BOX3EH

Power supply 230 V~ / 50 Hz 230 V~ / 50 Hz 24 V= 24 V=

Absorption 1.3 A 1.2 A 12 A 8 A

Torque 300 Nm 300 Nm 350 Nm 300 Nm

Openingtime 18 s 26 s 15÷30 s 15÷30 s

Service class 3 - FREQUENT 3 - FREQUENT 3 - FREQUENT 3 - FREQUENT

Intermittence S2 = 15 min

S3 = 25%

S2 = 15 min

S3 = 25%

S2 = 30 min

S3 = 50%

S2 = 30 min

S3 = 50%

Temperature -20° C / +55° C -20° C / +55° C -20° C / +55° C -20° C / +55° C

Degreeofprotection IP44

IP40 (with E1BOX)

IP44

IP40 (with E1BOX)

IP44 IP44

IP40 (with E1HBOX)

Control Panel E1BOX E1BOX VIVAH E1HBOX

Applications:

H = door wing height

L = door wing width

1x BOX

2x BOX

2. REFERENCE TO ILLUSTRATIONS

The given operating and performance features can only be gua-

ranteed with the use of DITEC accessories and safety devices.

2.1 Standardinstallationreferences(g.1-2)

[1] Gearmotor

[2] Courtesy light

[3] Casing

[4] Bottom casing

[5] Manual release

[6] Gearmotor shaft

[7] Base plate

[8] Safety edge

[9] Remote control

[10] Control panel

[11] Connect the power supply to a type-approved omnipolar

switch, with a contact opening distance of at least 3mm

(not supplied)

2.2 Accessories

BOXB2D Pair of straight arms

BOXB2C Pair of curved arms

BOXRL Side transmission

BOX2P Pair of extensions

BOXSL Fastening base L=2500

BOXRCG Central transmission

BOXAV1 Accessory for fastening onto wood

BOXG Coupling for poles

BOXA Pole

BOXSU Transmission support

BOXAS Grooved coupling

BOXGM Motor coupling

3. INSTALLATION

Unless otherwise specied, all measurements are expressed

in millimetres (mm).

3.1 Preliminary checks

Check the dimensions of the up and over door, the type of installa-

tion, the use limits of the gearmotor, and the necessary accessories.

3.2 Geared motor installation

- Remove the automation from its packaging.

Warning: the plastic parts are inserted but not xed.

- Remove the courtesy light [2], the casing [3] and the bottom

casing [4], then separate the gearmotor from the base plate

[7] by loosening the screws [A].

- Fix the base plate [7], respecting the measurements indi-

cated in g. 3-4-5.

Warning: using appropriate spacers or BOXSL, arrange a

solid fastening surface for the gearmotor at the height of

the frame of the up and over door.

- If using the BOXSL fastening plate:

- x the BOXSL on the up and over door;

- insert the gearmotor with the base plate [7] on the BOXSL

and fasten it with the 2 screws supplied.

- Fix the accessories, as shown in g. 6-7-8-9.

- Fix the corner-joint onto the upper frame of the up and over

door, in line with the motor arm, as shown (g.11A).

If it is not possible to assemble the corner-joint on the upper

part of the up and over door, refer to g.11B.

Warning: the dimensions of the poles, the position of the tran-

smissions, and the wall coupling for the corner-joint for resting

the arm must be established so that the motor arms do not

collide with the support arms of the up and over door. When it

is impossible to avoid the clashing with the tilting arm (with the

motor arms straight), use the curved motor arms BOXB2C.

After installing the motor(s) on the up and over door, release the

motor and check the door can be easily moved by hand. If the up

and over door is too heavy, it is essential to increase the weight

of the counterweights until the frame is fully balanced.

For up and over doors with L>2700mm, it is necessary to extend

the transmission shaft, using the accessories BOXA and BOXG.

For wooden up and over doors, use the accessory BOXAV1.

If the arms are not long enough, use the extensions BOX2P.

If you want to release the motor from the outside, using the key

5 m

4 m

3 m

2 m

1 m

1 m2 m3 m 4 m 5 m

5 m

4 m

3 m

2 m

1 m

1 m2 m3 m 4 m 5 m

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DITEC BOX3EH Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info