Bedienungsanleitung DJI INSPIRE 1 PRO (Seite 67 von 70) (Englisch)

611981

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

INSPIRE 1 PRO

User Manual

SD card slot on the camera.

Step 3- Update the Aircraft

1. Ensure the remote controller is powered off and then power on the aircraft. Upgrade will begin

automatically after aircraft is powered on.

2. It will take approximately 25 minutes to complete the rmware update. The camera status indicator

will blink green and red to indicate the upgrade is in progress and stop blinking when the update is

complete with success.

3. Check the upgrade status by opening the “.txt” le that is automatically generated after the update.

The update is successful if the text “result: successful” is in the document. Try upgrading the rmware

again if the text “result: failed” is found or the camera status indicator shows solid red.

Updating the Remote Controller Firmware

Ensure the DJI GO app has been updated to v1.2.0 before updating the remote controller. The

System Status bar in Camera View of the DJI GO App will ash several times if a rmware update is

available. Follow these steps to update the rmware via the DJI GO App.

Step 1- Check Battery and SD Card Capacity

1. The remote controller has at least 50% battery level.

2. Your mobile device is able to access the internet.

3. There is at least 30 MB of free space on your mobile device.

Step 2- Download and Update the Firmware

1. Go to the DJI GO App > Camera View > System Status bar > Overall Status. Tap Download the

firmware update package to download and update the firmware. Track the update progress from

progress bar in the DJI GO App. The status LED on the remote controller will blink blue during update

and blink green when update is complete with success.

Firmware update through the DJI GO app will not work with older versions of the remote controller

rmware. If the rmware update fails, follow the instructions below to update the rmware using the

traditional method:

a. Update the latest rmware package les from DJI ofcial web site.

b. Extract all downloaded les into the root directory of an SD card or USB ash drive.

c. Turn off the remote controller, Insert the SD card into a SD card reader or the USB disk onto the

remote controller USB port when remote controller is turned off.

d. Power on the remote controller and wait 60 seconds until the upgrade begins. Do not power off

the remote controller during the update.

e. It will take approximately 10 minutes to complete the rmware update. The camera will sound

a beeping sound and the Status LED on the remote controller shows solid blue to indicate the

update is in progress. The Status LED on remote controller shows solid green and beeping

sound will stop if the upgrade is completed with success.

f . If you do not have a SD card reader, you may insert the SD card into the gimbal and connect the

gimbal with remote controller to upgrade the remote controller.

You will only be able to update the remote controller rmware through the DJI GO app from

this point onwards.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DJI INSPIRE 1 PRO Seite 67

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DJI INSPIRE 1 PRO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info