Bedienungsanleitung DJI Matrice 300 RTK (Seite 22 von 100) (Englisch)

719096

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

MATRICE 300 RTK User Manual

Return-to-Home (RTH)

The Return-to-Home (RTH) function brings the aircraft back to the last recorded Home Point when

there is a strong GNSS signal. There are three types of RTH: Smart RTH, Low Battery RTH, and

Failsafe RTH. This section describes these three RTH types in detail.

GPS

Description

Home Point

If a strong GNSS signal was acquired before takeoff, the Home Point is

the location from which the aircraft launched. The GNSS signal strength is

indicated by the GNSS icon

. Less than 4 bars is considered a weak

GNSS signal. The aircraft status indicator will blink green rapidly when the

home point is recorded.

The aircraft can sense and avoid obstacles when the Forward Vision System is enabled and

lighting conditions are sufficient. To ensure the aircraft returns home while facing forward, it

cannot rotate or fly left and right during RTH.

Smart RTH

Use the RTH button on the remote controller and follow the on-screen instructions when GNSS is

available to initiate Smart RTH. The aircraft will then automatically return to the last recorded Home

Point. Use the remote controller to control the aircraft’s speed (pitch stick) or altitude (throttle stick)

to avoid a collision during the Smart RTH process. Press and hold the Smart RTH button once to

start the process, and press the Smart RTH button again to terminate the procedure and regain full

control of the aircraft.

Low Battery RTH

The low battery level failsafe is triggered when the DJI Intelligent Flight Battery is depleted to a point

that may affect the safe return of the aircraft. Users are advised to return home or land the aircraft

immediately when prompted. The DJI Pilot app will display a notice when a low battery warning is

triggered. The aircraft will automatically return to the Home Point if no action is taken after a ten-sec-

ond countdown. The user can cancel the RTH procedure by pressing the RTH button on the remote

controller. The thresholds for these warnings are automatically determined based on the aircraft’s

current altitude and distance from the Home Point. If the RTH procedure is cancelled following a

low battery level warning the Intelligent Flight Battery may not have enough charge for the aircraft to

land safely, which may lead to the aircraft crashing or being lost. Low Battery RTH can be turned off

in DJI Pilot app.

The aircraft will land automatically if the current battery level can only support the aircraft long

enough to descend from its current altitude. The user cannot cancel the auto landing but can use

the remote controller to alter the aircraft’s orientation during the landing process.

The Battery Level Indicator is displayed in the DJI Pilot app, and is described below:

12:29

Remaining flight time

Sufficient battery

level (Green)

Battery level Indicator

Power required to

return home (Yellow)

Critical Low battery

level warning

Low battery

level warning

Auto landing (Red)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DJI Matrice 300 RTK Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DJI Matrice 300 RTK

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info