1
2
MATRICE
TM
is a trademark of DJI.
Copyright
© 2016 DJI All Rights Reserved.
Learn more:
http://flysafe.dji.com/no-fly
No Fly Zones
It is important to understand basic flight guidelines for
the safety of both you and those around you.
Refer to the Disclaimer and Safety Guidelines for more
information.
Combination Stick Command
to start/stop the motors
Left stick up (slowly)
to take off
Left stick down (slowly)
until you touch the
ground.
Hold a few seconds to
stop the motors.
Lower
Ensure the landing gear is
lowered before landing.
OR
Manual T
Return-to-Home (RTH)
Bring the aircraft back to the Home
Point. Tap again to stop the procedure.
Intelligent Flight Modes
Tap to use Point of Interest (POI),
Waypoints and more.
Auto Landing
The aircraft will land vertically and stop
its motors.
Auto T
The aircraft will take off and hover at
an altitude of 4 feet (1.2 meters).
Before taking off, ensure the Aircraft
Status Bar in the DJI GO app indicates
‘Ready to Go (GPS)’.
Weak
Place your mobile
device and adjust the
clamp to secure.
Press the button to
release the clamp.
Connect your mobile
device with a USB
cable.
Unfold
High
●
Aircraft
Diagonal Wheelbase 1133 mm
Dimensions 1668 mm × 1518 mm × 727 mm with propellers,
frame arms and GPS mount unfolded (including landing gear)
437 mm × 402 mm × 553 mm with propellers,
frame arms and GPS mount folded (excluding landing gear)
Weight (with six TB47S batteries) 9.5 kg
Weight (with six TB48S batteries) 10 kg
Max Takeoff Weight Recommended 15.5 kg
Hovering Accuracy (P-GPS) Vertical: ±0.5 m, Horizontal: ±1.5 m
Max Angular Velocity Pitch: 300°/s, Yaw: 150°/s
Max Pitch Angle 25°
Max Wind Resistance 8 m/s
Max Ascent Speed 5 m/s
Max Descent Speed 3 m/s
Max Speed 40 mph / 65 kph (no wind)
Max Service Ceiling Above Sea Level 2170 propellers: 2500 m, 2195 propellers: 4000 m
Hovering Time* (with six TB47S batteries) No payload: 32 min, 6 kg payload: 16 min
Hovering Time* (with six TB48S batteries) No payload: 38 min, 5.5 kg payload: 18 min
Flight Control System A3 Pro
Supported DJI Gimbals Ronin-MX; ZENMUSE
TM
Z30, Zenmuse X5/X5R, Zenmuse X3, Zenmuse XT;
Zenmuse Z15 Series HD Gimbal: Z15-A7, Z15-BMPCC, Z15-5D III, Z15-GH4
Retractable Landing Gear Standard
Operating Temperature 14° to 104° F (-10° to 40° C)
●
Remote Controller
Operating Frequency 920.6 MHz to 928 MHz (Japan); 5.725 GHz to 5.825 GHz; 2.400 GHz to 2.483 GHz
Max Transmission Distance FCC Compliant: 3.1 mi (5 km), CE Compliant: 2.2 mi (3.5 km) (Unobstructed, free of interference)
Transmitter Power (EIRP) 10 dBm @ 900M, 13 dBm @ 5.8G, 20 dBm @ 2.4G
Video Output Port HDMI, SDI, USB
Operating Temperature 14° to 104° F (-10° to 40° C)
Battery 6000 mAh LiPo 2S
●
Charger (Model: MC6S600)
Voltage Output 26.1 V
Rated Power 600 W
Single Battery Port Output Power 100 W
●
Standard Battery (Model: TB47S)
Capacity 4500 mAh
Voltage 22.2 V
Battery Type LiPo 6S
Energy 99.9 Wh
Net Weight 595 g
Operating Temperature 14° to 104° F (-10° to 40° C)
Max Charging Power 180 W
●
Optional Battery (Model: TB48S)
Capacity 5700 mAh
Voltage 22.8 V
Battery Type LiPo 6S
Energy 129.96 Wh
Net Weight 680 g
Operating Temperature 14° to 104° F (-10° to 40° C)
Max Charging Power 180 W
Specifications
DJI incorporates HDMI
TM
technology.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC
in the United States and other countries.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
* Hovering time is based on flying at 10 meters above sea level in a no-wind
environment and landing with a 10% battery level.
Using Matrice 600 Pro
5. Preparing 1. Download DJI
Download and install DJI ASSISTANT
TM
2 on your computer via the website link below:
http://www.dji.com/matrice600-pro
Search ‘DJI GO’ in the App Store or Google Play, and download the app to your
mobile device.
●
DJI Assistant 2 supports Windows 7 (or later) or OS X 10.11 (or later).
●
DJI GO supports iOS 8.0 (or later) or Android 4.1.2 (or later).
DJI GO App
3. Charging Batteries
2. Checking Battery Levels
High
●
Press once to check
the battery level.
●
Press once, again
and hold to turn
on/off.
Make sure all six Intelligent Flight Batteries are fully charged before using the Matrice 600 Pro.
●
The Intelligent Flight Battery must be fully
charged before using it for the first time.
●
Only use the official DJI charger for your
Intelligent Flight Battery and remote
controller. Power off the Intelligent Flight
Battery before charging.
●
When charging is complete, the LED lights
on the Intelligent Flight Battery and remote
controller will turn off.
4. Preparing the Remote Controller
1
3
2
Download the detailed user manual at:
www
※ This content is subject to change without prior notice.
Designed by DJI. Printed in China.
●
The
takeoff. You should also use
In the DJI GO
6. Flight
DJI GO
App
●
Rotating propellers can be dangerous. Do not start the motors when there are people nearby.
●
Never stop the motors in mid-flight, or else the aircraft will crash.
●
Always keep your hands on the remote controller so long as the motor is still spinning.
●
DO NOT manually power on more than one Intelligent Flight Battery to avoid damaging
the batteries.
●
If powering on one of the six batteries does not trigger the others, follow the instructions
in the DJI GO app.
●
You only need to power off just one battery and all the other batteries will power off
automatically.
Mounting and Powering On Batteries
1. Make sure all six Intelligent Flight Batteries are fully charged and powered
off. Insert the batteries into the battery compartments.
2. Press the Power Button once, then press it again and hold for two seconds.
This will power on one of the six batteries, automatically triggering the others.
●
Ensure that all the Intelligent Flight Batteries are powered off before unfolding the aircraft.
●
Ensure that all the arrows on the GPS-Compass Pro point toward the front of the aircraft after unfolding them.
●
First-time activation requires your DJI account and internet connection.
Activating the Aircraft
When using your Matrice 600 Pro for the first time,
activate it in DJI Assistant 2 software. Connect the
Micro USB port of the Matrice 600 Pro to the
computer with a Micro USB cable and follow the
steps in DJI Assistant 2.
Unfolding the Aircraft
Power Outlet
100-240V
Mounting the
Landing Gear
Note the
orientation
Note the
orientation
Attach
Power on the
remote controller
Power on the aircraft Launch the DJI GO app
and enter Camera View
Ready to Go (GPS)
Return-to-Home (RC)
Manual Landing
Same as the RTH button in the DJI GO app.
Brings the aircraft back to the Home Point. Press
and hold to initiate the RTH procedure. Press again
to cancel.
