Bedienungsanleitung DJI Matrice 600 (Seite 19 von 74) (Englisch)

653250

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

MATRICE 600

User Manual

If the power supply is not OK when powering on the batteries, the DJI GO app will either prompt you

to adjust the battery positions or tell you there is a large voltage difference.

To adjust the battery positions:

1. Power off all the batteries.

2. Adjust battery positions by following the tips in the DJI GO app.

3. Ensure all the battery positions are correct and then power on one of the batteries. The other

batteries will power on automatically if the positions are correct.

If the message prompt says there is a large voltage difference, the power supply issue cannot be

resolved by adjusting the battery positions. Fully charge all the batteries and try again.

Powering Off:

Press the Power Button once, then press again and hold for 2 seconds to power off.

Ensure that all Intelligent Flight Batteries are operating normally before takeoff. If a battery

abnormal status appears in the DJI GO app, follow the on-screen instructions. The DJI GO

app will instruct you to land if a battery abnormality occurs during ight. In this event, you

should land and check the battery immediately.

Low Temperature Notice

1. Using the Intelligent Flight Battery at core temperatures below -10℃ is not advised. Between -10℃

and 5℃, the Intelligent Flight Battery should attain a voltage of 4.2 V, but it is recommended that

you apply the insulation sticker to the battery to prevent a rapid drop in temperature.

2. In cold environments (i.e. air temperature below 5℃), the performance of the Intelligent Flight

Battery is reduced. Ensure the Intelligent Flight Battery is fully charged and attains a voltage of 4.35

V before takeoff.

3. In very cold environments (e.g. air temperature of -20℃, battery core temperature of 5℃), the

Intelligent Flight Battery’s core temperature will drop rapidly even after pre-heating, and its

performance is signicantly reduced. It is not recommended to y under such conditions.

4. If the DJI GO app displays the Low Battery Level warning, stop flying and land the aircraft

immediately. You will still be able to control the aircraft’s movement when this warning is triggered.

5. For the optimal performance, maintain the Intelligent Flight Battery’s core temperature above 20℃

when in use.

Ensure the temperature of the Intelligent Flight Battery exceeds 5℃ before takeoff.

To warm up the battery, power on the Intelligent Flight Battery inside the battery compartment,

for approximately 1-2 minutes, before takeoff. Begin ying by hovering the aircraft at a low

altitude, for approximately 1 minute, to ensure the battery temperature is stable.

Checking the Battery Level

The Battery Level Indicator shows how much battery capacity is remaining. When the battery is

powered off, press the power button once. The Battery Level Indicator will light up to display the

current battery level. See the table below for details.

The Battery Level Indicator will show the current battery level during charging and discharging.

Its LEDs can exhibit the following behavior.

: LED is on. : LED is blinking.

: LED is off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DJI Matrice 600 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info