Bedienungsanleitung DJI Mavic Pro V1.2 (Seite 8 von 12) (Englisch)

653246

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

3. Charge the Batteries 5. Prepare the Aircraft1. Download the DJI GO 4 App and Watch the Tutorial Videos

Search for ‘DJI GO 4’ on the App Store or Google Play, or scan the QR code to

download the app on your mobile device. Watch the tutorial videos at www.dji.com

or in the DJI GO 4 App.

2. Check the Battery Levels 4. Prepare the Remote Controller

●

DJI GO 4 supports iOS 9.0 (or later) or Android 4.4 (or later).

●

Unfold the front arms and the propellers before the rear ones. All arms and propellers

must be unfolded before takeoff.

●

The gimbal cover is used to protect the gimbal. Remove it when necessary.

●

The Mavic Pro can be controlled using the Remote Controller or Virtual Joysticks.

Select control modes by toggling the Control Mode Switch. Only toggle this switch

when the aircraft is powered off.

Press once to check the battery level.

Press once, then again and hold to

turn on/off.

Press once to check the battery level on

LCD screen. Press once, then again and

hold to turn on/off the remote controller.

6. Prepare for Takeoff

7. Flight 8. Fly Safe

Before taking off, make sure the Aircraft Status

Bar in the DJI GO 4 app or on the Remote

Controller LCD screen displays 'Ready to Go'.

●

Turn on your mobile device's Wi-Fi and enter the Wi-Fi password shown on the front

arm to connect to the Mavic network if for any reason you cannot scan the QR code.

●

When using Wi-Fi in a wide open area with no Electro-Magnetic Interference,

transmission distance is approximately 262 ft (80 m) at an altitude of 164 ft (50 m).

●

The Wi-Fi frequency of your mobile device can be set to 2.4 Ghz or 5 Ghz. Set

your Wi-Fi to 5 Ghz for less interference. Once connected to the Mavic Pro, you

can change your Wi-Fi password or reset your Wi-Fi connection. (Refer to the

User Manual for more information)

The default flight control is known as Mode 2. The left stick controls the aircraft's

altitude and heading, while the right stick controls its forward, backward, left and right

movements. The gimbal dial controls the camera's tilt.

Charge Time:

~1 hour 20 minutes

Charge Time:

~2 hours

Use your DJI account to activate the aircraft. Activation requires an internet

connection.

Internet

●

Controlling flight with Virtual Joysticks on your mobile device via Wi-Fi

●

In the DJI GO 4 App

●

Watch the tutorial in the DJI GO 4 app or on the Official DJI website to learn more.

●

Always set an appropriate RTH altitude before takeoff. When the aircraft is

returning to the Home Point, you should guide it with the control sticks.

Battery Level: 100%

Remove Intelligent Flight Battery

High

Low

Battery Level

Power Outlet

100 - 240V

●

The motors can only be stopped mid-flight when the flight controller detects critical

error.

Left Stick

Right Stick

1. Toggle the Control Mode Switch to turn on Wi-Fi

2. Power on the aircraft

3. Launch the DJI GO 4 app and tap the icon on the top right of your screen, then

scan the Wi-Fi QR Code on the front arm to start connection

4. Tap Auto Takeoff

5. Fly the aircraft with touch control

MAVIC

and OCUSYNC

are trademarks of DJI.

DO NOT use the aircraft in adverse weather conditions such as rain,

snow, fog and wind speeds exceeding 10 m/s or 22 mph.

No Fly Zone

Learn more at:

http://flysafe.dji.com/no-fly

Stay away from the rotating propellers

and motors.

Launch the DJI GO 4 app

DJI GO 4

App

Power on the aircraftPower on the

remote controller

Ready to Go (GPS)

Combination stick

command to

start/stop the motors

Left stick up (slowly)

to take off

Left stick down (slowly) until you

touch the ground

Hold a few seconds to stop the

motors

TapFly

ActiveTrack

Auto Landing

Return-to-Home (RTH)

Normal

Fly in Open Areas

Strong GPS Signal

Maintain Line

of Sight

Fly Below

400 feet (120 m)

Avoid flying over or near obstacles, crowds, high voltage power lines, trees

or bodies of water.

DO NOT fly near strong electromagnetic sources such as power lines and

base stations as it may affect the onboard compass.

≥10m/s

It’s important to understand basic flight guidelines, for the safety of both you and

those around you. Don't forget to read the Disclaimer and Safety Guidelines.

Unfold the antennas and

the mobile device clamp.

Match propellers to motors

Marked Unmarked

Press the propeller

down firmly and rotate

in the lock direction

Unfold the front arms

and the propellers

Unfold the rear arms

and the propellers

Unfolded

Remove the gimbal

clamp from the camera

Mavic_XXX

WIFI RC

DJI GO 4

App

Auto Takeoff

Lightning connector cable (Connected)

and Standard Micro USB connector

cable included. Use as appropriate.

Strong

Weak

DJI GO 4 app and more information

Place one end of the RC

cable to the end of the slot.

USB Type-C connector cable is included.

Optional Reverse Micro USB connector

cable is available.

●

Choose an appropriate RC cable. Do not twist the RC cable.

●

The RC cable slider must be replaced if using a USB Type-C RC cable. Refer to the

User Manual for RC Cable connection.

YC.BZ.S01007.04

DJI Mavic Pro V1.2 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DJI Mavic Pro V1.2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info