Bedienungsanleitung DJI Phantom 2 Vision plus (Seite 49 von 52) (Englisch)

594198

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Appendix

Remote Controller

Operating Frequency 5.728 GHz - 5.85 GHz

Communication Distance (open area) CE Compliance: 400m; FCC Compliance: 800m

Receiver Sensitivity (1%PER) -93dBm

Transmitting Power (EIRP) CE Compliance: 25mW; FCC Compliance: 100mW

Working Current/Voltage 120mA@3.7V

Battery 2000mAh rechargeable LiPo battery

Range Extender

Operating Frequency 2412MHz - 2462MHz

Communication Distance (open area) 500m - 700m

Transmitting Power 20dBm

Power Consumption 2W

3 Troubleshooting (FAQ)

3.1 How to solve large margin(s) mid-point error?

If the Remote Controller stick(s) mid-point margin of error is too big, the motors will fail to start when you execute the

CSC and the Phantom will not take off. The below are some possible xes for this.

(1) One of the Remote Controller’s stick positions (except the throttle stick) is not centered when powering on the

Phantom 2 Vision+.

Solution: Place all Remote Controller sticks at their mid-point positions and then power cycle the Phantom 2 Vision+

to re-record the mid-point.

(2) The Remote Controller sticks have been trimmed, leading to a deviation in the mid-point position.

Solution: Use Assistant to perform a Remote Controller calibration.

a) Connect to Assistant, tap Basic -> RC -> Command Sticks Calibration and push all Remote Controller sticks

through their complete travel range to see if any stick cannot reach its outermost position.

b) Power cycle the Phantom 2 Vision+. Power cycling is required.

c) Re-attempt Remote Controller calibration in Assistant.

If the above solutions do not solve your issue, please send your Remote Controller to DJI Customer service for repair.

3.2 How to restore a video le if power is turned off during a recording session?

Solution: Keep or place the Micro-SD card back into the camera. Power cycle the camera and wait about 30 seconds for

the video le to be restored.

3.3 Failure to acquire the SSID.

Solution: Double check whether both the camera and Range Extender are powered on and the power switch of the

camera is switched to “Wi-Fi ON.”

3.4 What to do if Phantom 2 Vision+ is out of sight and the Wi-Fi connections is lost?

Solution: Turn off the Remote Controller to trigger the Failsafe mode and the aircraft will start to y back, descend, and

land at the Home point. Please make sure there are no obstacles between the Phantom and the home point and that you

are familiar with the procedure for regaining control.

3.5 Wi-Fi connection fails all the time.

Solution: Double check the current Wi-Fi connection status of the mobile device. The mobile device may be connecting

to other Wi-Fi networks after a connection breaks with the Phantom 2 Vision+.

3.6 Files fail to synchronize.

Solution: Video les that are too large (le sizes close to 4GB) cannot be synchronized to the mobile device. Some

mobile devices do not support the synchronization of the 1080i60 video les.

Appendix

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DJI Phantom 2 Vision plus Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DJI Phantom 2 Vision plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info