Bedienungsanleitung DLS CA12 (Seite 4 von 8) (Englisch)

66091

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Wiring

Power and Outputs

CA12

Power terminal ( +12V)

+12V REM GND

Remote terminal ( REM )

For RCA cable signal input:

Connect the radio power antenna lead = remote

turn on/off from the car stereo to the amplifier

remote connection. This turns on the amplifier

whenever the car stereo is turned on.

You can either use the built in remote cable in the

RCA cable itself or use a separate cable.

Sometimes a small disturbance may enter the

amplifier coming from the remote voltage , through

the built in remote wire and into the RCA cable.

Thus we recommend to use a separate remote wire

and run the RCA lead separate from remote wire,

power cables and speaker cables.

You can either use a crimp fork terminal or insert

the cable directly into the amplifier terminal. If there

is no remote voltage available from the stereo, you

must connect to the ignition key through the radio

or any accessories fuse.

DLS

DLS FH 1B

fuse holder

Connect to a good chassis ground. The ground

connection should be clean, unpainted metal to prov-

ide a good electrical connection. Use a wire brush, a

scraper or a piece of an abrasive sheet to clean the

metal. Use a lock washer or two to secure contact.

Protect with silicon grease or by paint applied

afterwards.

+12V REM GND

Power Light / Protect light

The power light (green ) comes on when

the amplifier is turned on.

The protect light ( red ) comes on when

the amplifier shuts down from

overheating or short circuit.

Fuses

Use only 30 ampere

ATC blade type fuses.

CA12 uses two 30

ampere fuses.

30A

For High Level input:

We recommend you to connect the remote wire as

described above.

The amplifier will be turned on/ turned off by the

high level input voltage. This is done when the Hi

level/Low level switch is set to Hi level position.

There is a small disadvantage that this function

gives soft turn on operation but some plop sound

when switching off.

You do not have to connect any remote voltage

when using Hi level input.

Connect the fuse holder as close to the vehicle

battery + as possible, using AWG5 = 16 mm

heavier cable. Use ring crimp terminal cable to

connect to battery +. Apply silicon grease to the

fuse to prevent corrosion.

Use a fuse holder for AGU fuses

like the DLS FH1B. Fuse value

60 A if you use a AWG5 cable.

Connect the battery cable to the +12 Volt on the

amplifier. If you want to improve the power capacity

you can add a Power capacitor of 1 Farad in parallel

with the DC input.

Be sure to use a rubber grommet or a plastic

insulating tube where the cable passes the firewall

or other places where it can easily be jammed.

Use wire ties to secure to existing cables in the engine

room.

Max. fuse value for different cable sizes:

6 mm

(9 AWG) :25 A 10 mm

(7AWG) :40 A

16 mm

(5AWG) :60 A 21 mm

(4AWG) :100 A

33 mm

(2AWG) :150 A 42 mm

(1AWG) :200

Protect

(Red)

Power

(Green)

Ground Terminal ( GND )

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DLS CA12 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info