Bedienungsanleitung DLS CAD 15 (Seite 5 von 12) (Englisch)

67778

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Important

Use either the low level or the high level input, do

not use both at same time.

Low level input

Use a pair of shielded stereo audio cables with RCA

type jack. Most trunk-mount amplifiers need a 20

feet RCA cable ( appr 5 – 6 meters). Most under

the seat installations require

12 feet ( 2 – 3 meters) RCA

cables. Avoid placing the RCA

cable close to speaker cables,

power cables and remote

control cable. Connect to in-

put socket A & B.

High Level Input

Connect left and right speaker wires coming from

the car stereo to the high level input as shown. You

must connect both plus and minus as the inputs

are balanced, connecting plus only gives lower level

and bad sound quality. By changing the polarity of

plus and minus, you can change the phase.

Hi level input plug on amp.

Automatic turn on when using high level input.

With the Hi/Low input swich set to Hi, the amplifier turns

on automatically on high input. You dont need to connect

a separate remote wire from your head unit.

When using High Level input:

Set the switch to position ”Hi / Level”

When using Low level input:

Set the switch to position ”Low / Level”

If the switch is set to wrong

position, the amplifier still

works, but the risk for

disturbances or distortion

increases.

Input and controls

Input Level control

Subsonic filter

The Subsonic filter blocks the very

deepest frequencies from reaching the

subwoofers. It has a variable

frequency from 15 to 50 Hz. A typical

setting is 25-30 Hz.

Low Pass Filter

The LPF ( low pass filter ) allow low

frequencies only and blocks higher

frequencies. A typical setting is 60 – 80

Hz. Choose the setting that sounds best

in your car.

Phase control

The phase control can be set

continuously from 0 - 180 degrees. This

is very useful when you want to adjust

the bass sound for best front stage

image.

Start at 0 and turn the control slowly

clockwise until you experience the bass

sound coming from the front.

You may have to change the polarity of

the speaker connection to get the best

result.

High Input

White : Ach.+

White/Black : A ch.-

Grey/Black : B ch.-

Grey : Bch.+

Input Wiring

Inputs may be low level from the RCA output of the car

stereo or high level from the car stereo speaker

output.Low level = RCA is to prefer for the best sound

quality.

Subsonic

15Hz 50Hz

LPF

15Hz 150Hz

The input level control, 5V – 0,15 V,

matches the output of your radio to the

input of the amplifier. After installation

is complete, make sure the input of the

amplifier is turned down all the way (

counter-clockwise at 5V ). Play a tape

or CD, make sure all bass or treble

settings or equalizer are flat, and turn

the volume of the radio up until you

just start to hear distortion. Turn the

volume control down just a bit. On the

amplifier increase the input level control

( clockwise or to the right ) until you just

start to hear distortion, then back the

level control just a bit. Now your radio

and amplifier levels are matched.

Level

5 V 0,15 V

Phase

180

Hi / Level

Low / Level

CAD 15

CAD11, CAD15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DLS CAD 15 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info