Bedienungsanleitung DLS cat 31 (Seite 9 von 12) (Englisch)

168767

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

NOISE PROBLEMS

WHINING NOISE VARYING WITH ENGINE

REVOLUTIONS:

Do this:

1. Rewire the power supply (24 V) to source

unit direct from battery.

2. Rewire ground wire from source unit to

clean position on chassis.

3. Check all power connections to ensure that

they are clean and tight.

4. Check quality of system ground connection.

5. Install a Power Cap capacitor. This can be

helpful against most noise problems.

CONSTANT WHINING NOISE:

Do this:

1. Ensure that all equipment has a common

ground point.

2. Check quality of earth strap connection from

battery negative terminal to chassis.

3. Disconnect signal cables from amplifier to

see if noise disappears. If so the leads are

picking up noise. Test this by laying a new

cable over the seats and reconnecting to the

amplifier. If the noise does not return, re-

route original cable away from source of

interference.

If noise remains regardless of cable position,

try to use so called Quasi-balanced signal

cables. DLS PRO or ULTIMATE cables are

quasibalanced.

SPEAKER POLARITY CHECK.

All speakers in a car audio system should be

connected in phase (the same polarity). All speaker

cones must move in the same direction. Out of

phase speakers will cause a lack of bass, and a

poor stereo soundstage.

Checking polarity:

Hold the - connection of the speaker wire to the -

terminal of a 1,5 Volt flashlight battery. Tap the +

wire on to the + terminal of the battery, and observe

the movement of the cone. The cone should move

outwards when the wire touches the battery, and

inwards when the battery is removed. If it is the

other way around, the speaker has been connected

backwards and it must be removed and connected

correctly.

If your system also has a subwoofer connected

through a passive 6 or 12 dB crossover, try to

connect this with various polarity and judge what

sounds best. The phase shift in passive crossovers

sometimes makes it necessary to change polarity.

Batteri

1,5 Volt

Professional Tip:Professional Tip:

Professional Tip: Professional Tip:

Installing in trunk

When installing the amplifier in the trunk, run the

power wires along the same path as the other vehicle

wiring. Many cars have insulated channels for wiring.

you will have to remove the door sill trim and the

carpet.

Securing wires

Use wire ties to bundle together when possible.

(But never bundle speaker wires or signal cables

together with power wires.

Professional Tip:

Speaker and power wires

Do not run speaker and power wires next to each

other. Power wires can generate a ”siren” sound in

the speakers. Runs speaker and power wires on

opposite sides of the vehicle.

Crimp connections

Purchase crimp connectors and crimping tool.

Connectors are color coded.

1. Strip 1/4 inch (6 mm) of insulation from the wire.

2. Insert into connector

3. Crimp tightly

CAT31

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DLS cat 31 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info