Bedienungsanleitung Dolmar 109 HappyStart (Seite 12 von 28) (Englisch)

507647

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Chain oil

Use an oil with adhesive additive for lubricating the chain and

guide bar. The adhesive additive prevents the oil from being

ß ung off the chain too quickly.

We recommend the use of chain oil which is bio-degradable in

order to protect the environment. The use of bio-degradable oil

may even be required by local regulations.

The chain oil BIOTOP sold by DOLMAR is made of special

vegetable oils and is 100% bio-degradable. BIOTOP has been

granted the "blue angel" (Blauer Umweltschutz-Engel) for being

particularly environment-friendly (RAL UZ 48).

BIOTOP chain oil is available in the following sizes:

1 l order number 980 008 210

5 l order number 980 008 211

20 l order number 980 008 213

Bio-degradable oil is stable only for a limited period of time. It

should be used within 2 years from the date of manufacture

(printed on the container).

Important note on bio-degradable chain oils:

If you are not planning to use the saw again for an extended

period of time, empty the oil tank and put in a small amount of

regular engine oil (SAE 30), and then run the saw for a time.

This is necessary to ß ush out all remaining bio-degradable oil

from the oil tank, oil-feed system, chain and guide bar, as many

such oils tend to leave sticky residues over time, which can

cause damage to the oil pump or other parts.

The next time you use the saw, Þ ll the tank with BIOTOP chain

oil again.

NEVER USE WASTE OIL

Waste oil is very dangerous for the environment.

Waste oil contains high amounts of carcinogenic substances.

Residues in waste oil result in a high degree of wear and tear

at the oil pump and the sawing device.

In case of damage caused by using waste oil or unappropriate

chain oil the product guarantee will be null and void.

Your salesman will inform you about the use of chain oil.

waste oil

Fuel / Refuelling

1000 cm

(1 litre) 20 cm

20 cm

10 cm

5000 cm

(5 litres) 100 cm

100 cm

50 cm

10000 cm

(10 litres) 200 cm

200 cm

100 cm

100:1

Gasoline

50:1

OIL

Fuel mixture

This tool is powered by a high-performance air-cooled two-

stroke engine. It runs on a mixture of gasoline and two-stroke

engine oil.

The engine is designed for unleaded regular gasoline with a min.

octane value of 91 ROZ. In case no such fuel is available, you can

use fuel with a higher octane value. This will not affect the engine.

In order to obtain an optimum engine output and to protect your

health and the environment use unleaded fuel only.

To lubricate the engine, use a synthetic oil for two-stroke air-

cooled engines (quality grade JASO FC or ISO EGD), which has

to be added to the fuel. The engine has been designed for use of

DOLMAR HP 100 high-performance two-stroke engine oil and a

mixture ratio of only 100:1 to protect the environment. In addition, a

long service life and reliable operation with a minimum emission of

exhaust gases are ensured.

DOLMAR HP 100 high-performance two-stroke engine oil is avail-

able in the following sizes:

0,5 l order number 980 008 109

DOLMAR high-performance two-stroke engine oil is available in the

following sizes to suit your individual requirements:

1 l order number 980 008 107

100 ml order number 980 008 106

In case DOLMAR high-performance two-stroke engine oil is not

available, it is urgently recommended to use a mixture ratio of 50:1

with other two-stroke engine oils, as otherwise optimum operation

of the engine cannot be guaranteed.

Caution: Do not use ready-mixed fuel from petrol stati-

ons.

The correct mixture ratio:

50:1 when using DOLMAR high-performance two-stroke engine

oil, i. e. mix 50 parts gasoline with 1 part oil.

100:1 when using DOLMAR HP 100 high-performance two-stroke

engine oil, i. e. mix 50 parts gasoline with 1 part oil.

50:1 when using other synthetic two-stroke engine oils

(quality grade JASO FC or ISO EGD), i. e. mix 50 parts

gasoline with 1 part oil.

NOTE: For preparing the fuel-oil mixture Þ rst mix the entire oil quantity

with half of the fuel required, then add the remaining fuel. Thoroughly

shake the mixture before Þ lling it into the chain saw tank.

It is not wise to add more engine oil than speciÞ ed to ensure

safe operation. This will only result in a higher production of

combus-tion residues which will pollute the environment and

clog the exhaust channel in the cylinder as well as the mufß er.

In addition, fuel consumption will rise and performance will

decrease.

The Storage of Fuel

Fuels have a limited storage life. Fuel and fuel mixtures age through

evaporation, especially at high temperatures. Aged fuel and fuel

mixtures can cause starting problems and damage the engine.

Purchase only that amount of fuel, which will be consumed over

the next few months. At high temperatures, once fuel has been

mixed it should be used up in 6-8 weeks.

Store fuel only in proper containers, in dry, cool, secure

locations!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dolmar 109 HappyStart Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dolmar 109 HappyStart

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info