Bedienungsanleitung Dolmar AH-1852H (Seite 8 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

507694

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Installing or removing battery cartridge

CAUTION:

• Hold the tool and the battery cartridge firmly when

installing or removing battery cartridge. Failure to

hold the tool and the battery cartridge firmly may cause

them to slip off your hands and result in damage to the

tool and battery cartridge and a personal injury. (Fig. 1)

• Always switch off the tool before installing or removing

of the battery cartridge.

• To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

• To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If you can see the red indicator

on the upper side of the button, it is not locked

completely. Install it fully until the red indicator cannot

be seen. If not, it may accidentally fall out of the tool,

causing injury to you or someone around you.

Do not use force when installing the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Battery protection system (Lithium-ion

battery with star marking) (Fig. 2)

Lithium-ion batteries with a star marking are equipped

with a protection system. This system automatically cuts

off power to the tool to extend battery life.

The tool will automatically stop during operation if the tool

and/or battery are placed under one of the following

conditions:

• Overloaded:

The tool is operated in a manner that causes it to

draw an abnormally high current.

In this situation, release the trigger switch on the tool

and stop the application that caused the tool to

become overloaded. Then pull the trigger switch

again to restart.

If the tool does not start, the battery is overheated. In

this situation, let the battery cool before pulling the

trigger switch again.

• Low battery voltage:

The remaining battery capacity is too low and the tool

will not operate. In this situation, remove and

recharge the battery.

Switch action

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released. (Fig. 3)

For your safety, this tool is equipped with a dual switching

system. To turn on the tool, press the lock-off button and

triggers A and B. Release either one of the two pressed

triggers to turn off. The sequence of switching is

unimportant as the tool only starts when both switches are

activated.

Indication lamp (Fig. 4)

Running the tool allows the indication lamp to show the

battery cartridge capacity status.

When the tool is also overloaded and has stopped during

operation, the lamp lights up in red.

Refer to the following table for the status and action to be

taken for the indication lamp.

Note 1: The time at which the indication lamp lights up varies by the temperature around the work area and the battery

cartridge conditions.

010970

OPERATION

CAUTION:

• Be careful not to accidentally contact a metal fence or

other hard objects while trimming. The blade will break

and may cause serious injury.

• Overreaching with a hedge trimmer, particularly from a

ladder, is extremely dangerous. Do not work from

anything wobbly or infirm. (Fig. 5)

Do not attempt to cut branches thicker than 10 mm

diameter with this trimmer. These should first be cut with

shears down to the hedge trimming level.

CAUTION:

• Do not cut off dead trees or similar hard objects.

Failure to do so may damage the tool. (Fig. 6)

Hold the trimmer with both hands and pull the switch

trigger A or B and then move it in front of your body.

(Fig. 7)

As a basic operation, tilt the blades towards the trimming

direction and move it calmly and slowly at the speed rate

of 3 - 4 seconds per meter. (Fig. 8)

To cut a hedge top evenly, it helps to tie a string at the

desired hedge height and to trim along it, using it as a

reference line. (Fig. 9)

Indication lamp Status Action to be taken

The lamp blinks in red This indicates the appropriate time to

replace the battery cartridge when the

battery power becomes low.

Recharge the battery cartridge as soon

as possible.

The lamp lights up in red.

(Note 1)

This function works when the battery power

is almost used up. At this time, tool stops

immediately.

Recharge the battery cartridge.

The lamp lights up in red.

(Note 1)

Autostop due to overload

Turn off the tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dolmar AH-1852H Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info