Bedienungsanleitung Dolmar AK3622 (Seite 10 von 24) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

507717

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

011713

• When only the lowermost indicator lamp (next to the

“E”) blinks, or when none of the indicator lamps light,

the battery capacity has run out, so the tool does not

operate. In these cases, charge the battery or replace

the empty battery with a fully charged one.

• When two or more indicator lamps do not light even

after charging is complete, the battery has reached the

end of its service life.

• When the upper two and lower two indicator lamps light

alternately, the battery may have malfunctioned.

Contact your local Dolmar authorized service center.

NOTE:

• The indicated capacity may be lower than the actual

level during use or immediately after using the tool.

• Depending on the conditions of use and the ambient

temperature, the indication may differ slightly from the

actual capacity.

Battery converters (optional accessory)

WARNING:

• Before installing or removing the battery converters

AA-3618/AA-3618CL, remove the lock key.

AA-3618 (optional accessory)

WARNING:

• When using the AA-3618, be sure to use the holder

(optional accessory) to retain its cord. Failure to use

the holder leaves the cord loose. This may cause the

cord to be entangled by the blade, resulting in damage

to the tool and a personal serious injury.

• When using the AA-3618, never attach it to any part of

your body. Attaching the AA-3618 to any part of your

body may cause a serious injury. (Fig. 5)

Hook the battery converter AA-3618 onto installation

section of the handle.

Holder (optional accessory)

When using the AA-3618, be sure to use the holder

(optional accessory) to retain its cord. (Fig. 6)

Fit the holder (optional accessory) in the hole on the left

side of the handle from the operator’s view. And then

push the cord into the holder so that the cord tension is

not too loose. Make sure the cord is secured with the cord

holder. (Fig. 7)

Open out the battery hood and then slide all the way and

click the product mounting adapter of the AA-3618 into the

battery port 1. (Fig. 8)

Pull up lightly and remove the rubber cap from the slit in

the lower housing as shown in the figure.

NOTE:

• Do not pull up the rubber cap forcibly because forcing it

may damage its retaining section. (Fig. 9)

Bend the cord of the battery converter AA-3618 over the

product attachment section. Then run the cord of the AA-

3618 through the slit in the lower housing and close the

battery hood.

To remove the AA-3618, follow the installation procedure

in reverse.

AA-3618CL (optional accessory) (Fig. 10)

Open the battery hood and click in the AA-3618CL into

the battery port. Close the battery hood.

To remove the AA-3618CL, press on the hook of the AA-

3618CL and withdraw it with both hands.

Indication lamp

WARNING:

• Do not use the battery selection switch during the

operation.

• After flipping the battery selection switch, the main

switch is turned off. To start the tool, the operator

needs to press the main switch. (Fig. 11 & 12)

You can switch the battery by flipping the battery selection

switch when the tool is equipped two batteries. (The

indication lamps shows the status No. 1 or No. 6.)

If the tool is equipped one battery, flip the battery button to

chose one side which the battery is equipped.

• If the tool is equipped one battery and you switch to a

battery port in which no battery cartridge is mounted,

the indication lamps shows the status No. 2 or No. 5.

The warning lamp lights up when a problem occurs, and

the tool is automatically switched off about 10 seconds

after the warning lamp has lighted. The indication of the

warning lamp means as follows.

• Lighting-up-red: There are two possibility why the red

lamp lights up.

• The motor is overheated. (The indication lamp

shows the status No. 3.)

Turn off the main switch, and restart the tool after

the motor cools down.

• The battery capacity is low. (The indication lamp

shows the status No. 2 or No. 5.)

Turn off the main switch, and recharge the battery

cartridge.

• Blinking red: The blade becomes overloaded by

getting stuck because of digging too deep, or clogged

up by weeds or stone. (The indication lamp display

shows the status No. 4.)

Switch off the tool by pressing the main switch, lift the

blade by holding the handle, and check whether a

obstacle blocks the blade.

CAUTION:

• Always switch off the tool and remove the battery

cartridge before removing the obstacle.

Indicator lamps

Remaining capacity

Lighted Off Blinking

E F

70% to 100%

45% to 70%

20% to 45%

0% to 20%

Charge the battery.

The battery may

have malfunctioned.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dolmar AK3622 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info