Bedienungsanleitung Dolmar AT-1826H (Seite 10 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

598405

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

PARTS DESCRIPTION (Fig. 2)

FUNCTIONAL DESCRIPTION

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before adjusting or

checking function on the tool. Failure to switch off

and remove the battery cartridge may result in serious

personal injury from accidental start-up.

Installing or removing battery cartridge

CAUTION:

• Hold the tool and the battery cartridge firmly when

installing or removing battery cartridge. Failure to

hold the tool and the battery cartridge firmly may cause

them to slip off your hands and result in damage to the

tool and battery cartridge and a personal injury.

• Always switch off the tool before installing or removing

the battery cartridge.

To remove the battery cartridge, slide it from the tool while

sliding the button on the front of the cartridge. (Fig. 3)

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip it

into place. Always insert it all the way until it locks in place

with a little click. If you can see the red indicator on the

upper side of the button, it is not locked completely. Install

it fully until the red indicator cannot be seen. If not, it may

accidentally fall out of the tool, causing injury to you or

someone around you.

NOTE:

• Do not use force when installing the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Battery protection system (Lithium-ion

battery with star marking) (Fig. 4)

Lithium-ion batteries with a star marking are equipped

with a protection system. This system automatically cuts

off power to the tool to extend battery life.

The tool will automatically stop during operation if the tool

and/or battery are placed under one of the following

conditions:

• Overloaded:

The tool is operated in a manner that causes it to

draw an abnormally high current.

In this situation, release the trigger switch on the tool

and stop the application that caused the tool to

become overloaded. Then pull the trigger switch

again to restart.

If the tool does not start, the battery is overheated. In

this situation, let the battery cool before pulling the

trigger switch again.

• Low battery voltage:

The remaining battery capacity is too low and the tool

will not operate. In this situation, remove and

recharge the battery.

Power switch action

WARNING:

• Before inserting the battery cartridge in the tool,

always check to see that the switch trigger

actuates properly and returns to the “OFF”

position when released. Do not pull the switch

trigger hard without pressing in the lock-off button.

This can cause switch breakage. Operating a tool

with a switch that does not actuate properly can lead to

loss of control and serious personal injury.

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided.

To start the tool, move the lock-off button forward and pull

the switch trigger. Release the switch trigger to stop.

(Fig. 5)

Indication lamp (Fig. 6)

Running the tool allows the indication lamp to show the

battery cartridge capacity status.

When the tool is also overloaded and has stopped during

operation, the lamp lights up in red.

Refer to the following table for the status and action to be

taken for the indication lamp.

Note 1: The time at which the indication lamp lights up varies by the temperature around the work area and the battery

cartridge conditions.

012443

Adjusting the shaft length

WARNING:

• Before adjusting the shaft length, release the switch

trigger and remove the battery cartridge from the string

trimmer. Failure to release the trigger and removing the

battery cartridge may cause a personal injury.

To adjust the length of the shaft, turn the grip

counterclockwise until the shaft is unlocked and pull out or

push in to the desired length. (Fig. 7)

Nylon cutting head

NOTICE:

• The bump feed will not operate properly if the nylon

cutting head is not rotating.

Indication lamp Status Action to be taken

The lamp blinks in red. This indicates the appropriate time to

replace the battery cartridge when the

battery power becomes low.

Recharge the battery cartridge as soon

as possible.

The lamp lights up in red.

(Note 1)

This function works when the battery

power is almost used up. At this time,

tool stops immediately.

Recharge the battery cartridge.

The lamp lights up in red.

(Note 1)

Autostop due to overload. Turn off the tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dolmar AT-1826H Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info