Bedienungsanleitung Dolmar ES-33A (Seite 28 von 189) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

507643

Zoom out

Zoom in

Vorherige Seite

1/189

Nächste Seite

2. Keep the chain saw in a secure, dry and locked room

out of the reach of children. Do not store the chain saw

outdoors.

Maintenance

1. Withdraw the plug from the socket before carrying out

any adjustments or maintenance.

2. Check the power cable regularly for damage to the

insulation.

3. Clean the chain saw regularly.

4. Have any damage to the plastic housing repaired

properly and immediately.

5. Do not use the saw if the switch trigger is not working

properly. Have it properly prepared.

6. Under no circumstances should any modifications be

made to the chain saw. Your safety is at risk.

7. Do not carry out maintenance or repair work other

than that described in this instruction manual. Any

other work must be carried out by DOLMAR Service.

8. Only use original DOLMAR replacement parts and

accessories intended for your model of saw. The use

of other parts increases the risk of accident.

9. DOLMAR accepts no responsibility for accidents or

damage should non-approved bars, saw chains or

other replacement parts or accessories be used. Refer

to the “Extract from the spare parts list” for approved

saw bars and chains.

First aid

................... Do not work alone. Always work within

shouting distance of a second person.

1. Always keep a first-aid box to hand. Replace any

items taken from it immediately.

2. Should you request assistance in the event of an acci-

dent, state the following:

• Where did the accident happen?

• What happened?

• How many persons are injured?

• What injuries do they have?

• Who is reporting the accident?

NOTE:

Individuals with poor circulation who are exposed to

excessive vibration may experience injury to blood ves-

sels or the nervous system.

Vibration may cause the following symptoms to occur in

the fingers, hands or wrists: “Falling asleep “(numbness),

tingling, pain, stabbing sensation, alteration of skin colour

or of the skin.

If any of these symptoms occur, see a physician!

SAVE THESE INSTRUCTIONS

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Switch action (Fig. 5)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided.

To start the tool, depress the lock-off button and pull the

switch trigger.

Release the switch trigger to stop.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing saw chain

CAUTION:

• Always be sure that the tool is switched off and

unplugged before installing or removing the saw chain.

• Always wear gloves when installing or removing the

saw chain.

1. To remove the saw chain, move the lever in the

upright position. (Fig. 6)

2. Press the lever and with the lever pressed in, turn it

counterclockwise to loosen the nut until sprocket

cover comes off. (Pressing in the lever leads to the fit-

ting of lever into the nut.)

3. Turn the adjusting dial counterclockwise to release the

saw chain tension.

4. Remove the sprocket cover.

5. Remove the saw chain and guide bar from the chain

saw.

6. To install the saw chain, fit in one end of the saw chain

on the top of the guide bar and the other end of it

around the sprocket. (Fig. 7)

At this time, fit the saw chain as shown in the figure

because it rotates in the direction of arrow.

7. Rest the guide bar in place on the chain saw.

8. Turn the adjusting dial counterclockwise to slide the

adjusting pin in the direction of arrow. (Fig. 8)

9. Place the sprocket cover on the chain saw so that the

hook at its back cover is inserted into a hole in the

chain saw and the adjusting pin is positioned in a

small hole in the guide bar. (Fig. 9)

10. Press in the lever and with the lever depressed turn it

fully clockwise to tighten the nut. Then make it about a

quarter turn counterclockwise to loosen the nut lightly.

(Fig. 10)

Adjusting saw chain tension

The saw chain may become loose after many hours of

use. From time to time check the saw chain tension

before use.

Move the lever in the upright position. (Fig. 11)

Press in the lever. With the lever depressed, make a quar-

ter turn on it counterclockwise to loosen the nut lightly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dolmar ES-33A Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info