Bedienungsanleitung Dolmar ES-34 TLC (Seite 12 von 28) (Englisch, Holländisch)

599929

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

follow the safety rules stated in this instruction

manual may cause serious personal injury.

DESIGNATION OF PARTS (Fig. 5)

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Removing or installing saw chain

CAUTION:

• Always wear gloves when installing or removing the

saw chain.

To remove the saw chain, perform the following steps:

1. Press and fully open the lever until it stops. (Fig. 6)

2. Turn the lever counterclockwise to loosen the sprocket

cover until it comes off.

3. Turn the adjusting dial to “-” direction to release the

saw chain tension. (Fig. 7)

4. Remove the sprocket cover.

5. Remove the saw chain and guide bar from the chain

saw.

To install the saw chain, perform the following steps:

6. Make sure the direction of the chain. The arrow mark

on the chain shows the direction of the chain. (Fig. 8)

7. Fit in one end of the saw chain on the top of the guide

bar and the other end of it around the sprocket.

8. Rest the guide bar in place on the chain saw.

9. Align the tension slide with the hole of the guide bar.

(Fig. 9)

10. Holding the guide bar, and turn the adjusting dial to “+”

direction to adjust the saw chain tension.

11. Place the sprocket cover so that the hooks fit

alongside the holes and the pin fits its counterpart on

the sprocket cover. (Fig. 10)

12. Turn the lever clockwise to secure the sprocket cover.

(Fig. 11)

13. Press and return the lever to its original position.

Adjusting saw chain tension

The saw chain may become loose after many hours of

use. From time to time check the saw chain tension

before use.

1. Press and fully open the lever until it clicks. Turn it

counterclockwise a little to loosen sprocket cover

lightly. (Fig. 6)

2. Lift up the guide bar tip slightly. (Fig. 12)

3. Turn the adjusting dial to adjust the saw chain tension.

Tighten the saw chain until the lower side of the saw

chain fits in the guide bar rail (see circle).

4. Keep holding the guide bar lightly, tighten the sprocket

cover after adjusting the chain tension. Make sure that

the saw chain does not loose at lower side.

5. Press and return the lever to its original position.

(Fig. 13)

Make sure the saw chain fits snugly against the lower side

of the bar.

CAUTION:

• Do not tighten the saw chain too much. Excessively

high tension of saw chain may cause breakage of saw

chain, wear of the guide bar and breakage of the

adjusting dial.

• A chain which is too loose can jump off the bar, and

therefore presents an accident risk.

• Carry out the procedure of installing or removing saw

chain in a clean place free from sawdust and the like.

Engaging extension cord

CAUTION:

• Make sure that the extension cord is unplugged to the

mains outlet. (Fig. 14)

When engaging the extension cord, secure it to the chain

saw’s cord with the cord hook.

Attach the cord hook about 100 - 200 mm from the

extension cord connector. This helps prevent

unintentional disconnection.

OPERATION

Switch action (Fig. 15)

CAUTION:

• Always be sure that the tool is switched off and

unplugged before checking function on the switch

trigger.

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

NOTE:

• Do not turn on and off too often within a short time (five

seconds or less). The temperature inside the tool will

rise and may cause the tool damage. The time varies

by atmosphere temperature and other conditions.

(Fig. 16)

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided.

To start the tool, depress the lock-off button and pull the

switch trigger. Release the switch trigger to stop.

Lubrication

CAUTION:

• Always be sure that the tool is switched off and

unplugged before lubricating the saw chain.

Lubricate the saw chain and bar using biologically

degradable saw chain oil with an adhesion agent. The

adhesion agent in the saw chain oil prevents the oil from

being thrown off the saw excessively quickly. Mineral oils

must not be used, as they are harmful to the environment.

(Fig. 17)

CAUTION:

• Prevent the oil from coming into contact with the skin

and eyes. Contact with the eyes causes irritation. In the

event of eye contact, flush the affected eye

immediately with clear water, then consult a doctor at

once.

• Never use waste oil. Waste oil contains carcinogenic

substances. The contaminants in waste oil cause

accelerated wear of the oil pump, the bar and the

chain. Waste oil is harmful to the environment.

• When filling the chain saw with chain oil for the first

time, or refilling the tank after it has been completely

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dolmar ES-34 TLC Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info