Bedienungsanleitung Dolmar HT-2375D (Seite 15 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

507691

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

For any maintenance or adjustment not described in this manual, ask your local DOLMAR authorized service center.

Daily checkup and maintenance

To ensure a long service life and to avoid any damage to the equipment, the following servicing operations should be performed at regular

intervals.

- Before use;

• Check the machine for loose screws or missing parts. Pay particular attention to the tightness of the cutter blade screws.

• Check for clogging of the cooling air passage and the cylinder ns. Clean them if necessary.

• Clean and check the fuel tank for fuel leakage or foreign object in the tank.

- After use;

• Clean the hedge trimmer externally and inspect for damage.

• Clean the air lter. When working under extremely dusty conditions, clean the lter several times a day.

• Check the blades for damage and make sure they are rmly mounted.

Checking the spark plug

Check and clean the spark plug daily or every 8 operating hours.

- Only use the supplied universal wrench to remove or install the spark plug.

- The gap between the two electrodes of the spark plug should be 0.7 to

0.8 mm. If the gap is too wide or too narrow, adjust it. If the spark plug is

clogged with carbon or fouled, clean it thoroughly or replace it. Use an exact

replacement.

0.7 - 0.8 mm

Grease nipple

Tank cap

Fuel pipe

Supplying grease and lubricant

- Supply grease through the grease nipple every 50 operating hours. (Shell

Alvania No. 3 or equivalent)

NOTE: Be sure to observe the specied time and amount of grease supply.

Otherwise an insufcient grease supply will cause a machine trouble.

Cleaning the fuel lter (suction head in the fuel tank)

WARNING: Inammables strictly prohibited

Check and clean the fuel lter monthly or every 50 operating hours.

- The felt lter (1) of the suction head is used to lter the fuel required by the

carburetor.

- Visually check the felt lter regularly.

- To check the felt lter, open the tank cap, use a wire hook and pull out the

suction head through the tank opening.

Replace the felt lter if it has hardened, been contaminated or be clogged.

- Replace the felt lter at least quarterly to ensure an enough fuel supply to the

carburetor. Otherwise an insufcient fuel supply will cause the engine start

failure and limited maximum speed.

Replacing the fuel pipe

CAUTION: Inammables strictly prohibited

Check and clean the fuel pipe daily or every 10 operating hours.

Replace the fuel pipe every 200 operating hours or every year regardless of

operating frequency. Otherwise fuel leakage may lead to re.

If you nd any leakage during inspection, replace the oil pipe immediately.

Replacing the tank cap

- If there is any aw or damage on the tank cap, replace it.

- The tank cap wears out in course of time. Replace it every two or three years.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dolmar HT-2375D Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info