Bedienungsanleitung Dolmar HT-2460 (Seite 15 von 31) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

507692

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

Any maintenance or adjustment work that is not included and described in this manual is to be performed by Authorized Service Agent only.

Daily checkup and maintenance

To ensure a long service life and to avoid any damage to the equipment, the following servicing operations should be performed at regular

intervals.

- Before operation, check the machine for loose screws or missing parts. Pay particular attention to the tightness of the cutter blade screws.

- Before operation, always check for clogging of the cooling air passage and the cylinder ns. Clean them if necessary.

- Perform the following work daily after use:

• Clean the Hedge Trimmer externally and inspect for damage.

• Clean the air lter. When working under extremely dusty conditions, clean the lter several times a day.

• Check the blades for damage and make sure they are rmly mounted.

Checking the spark plug - Every 8 hours (Daily)

- Only use the supplied universal wrench to remove or to install the spark plug.

- The gap between the two electrodes of the spark plug should be 0.7 to

0.8 mm. If the gap is too wide or too narrow, adjust it. If the spark plug is

clogged with carbon or fouled, clean it thoroughly or replace it. Use an exact

replacement.

0.7 - 0.8 mm

Grease nipple

(1)

Tank cap

Fuel pipe

Supply of grease and lubricant

- Supply grease from the grease nipple every 50 operating hours. (Shell

Alvania No. 3 or equivalent)

NOTE:

Be sure to observe the specied time and amount of grease supply.

If the grease supply is not made at the specied interval or if the amount

of grease supplied is not sufcient, the machine may fall into a trouble

because of lack of grease.

CLEANING OF FUEL FILTER

WARNING: INFLAMMABLES STRICTLY PROHIBITED

Interval of Cleaning and Inspection: Monthly (every 50 operating hours)

Suction head in the fuel tank

- The felt lter (1) of the suction head is used to lter the fuel required by the

carburetor.

- A periodical visual inspection of the felt lter is to be conducted.

- For that purpose, open the tank cap, use a wire hook and pull out the suction

head through the tank opening.

Filters found to have hardened, been polluted or clogged up are to be

replaced.

- Insufcient fuel supply can result in the admissible maximum speed being

exceeded. It is therefore important to replace the felt lter at least quarterly to

ensure satisfactory fuel supply to the carburetor.

REPLACEMENT OF FUEL PIPE

CAUTION: INFLAMMABLES STRICTLY PROHIBITED

Interval of Cleaning and Inspection: Daily (every 10 operating hours)

Replacement: Annually (every 200 operating hours)

Replace the fuel pipe every year, regardless of operating frequency. Fuel

leakage may lead to re.

If any leakage is detected during inspection, replace the oil pipe immediately.

REPLACEMENT OF TANK CAP

- If there is any aw or damage on the tank cap, replace it.

- The tank cap is consumable, and therefore should be renewed every two to

three years.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dolmar HT-2460 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info