Bedienungsanleitung Dolmar HT-2475 (Seite 12 von 31) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

507693

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

- Never operate with a loose grip.

- Never touch the cutting device when starting the engine and during operation.

- Operate the Hedge Trimmer in such a manner as to avoid inhalation of the

exhaust gases. Never run the engine in enclosed rooms (Risk of gas poisoning).

Carbon monoxide is an odorless gas.

- All protective installations and guards supplied with the machine must be used

during operation.

- Never operate the engine with a faulty exhaust mufer or if it is missing.

- Use the Hedge Trimmer only in good light and visibility.

- During the winter season beware of slippery or wet areas, ice and snow. (Risk of

slipping.) Always ensure a safe footing.

- Never stand on a ladder and run the Hedge Trimmer. Keep both feet on the

ground.

- Never climb up the trees with the Hedge Trimmer to perform cutting operation.

- Never work on unstable surfaces.

- Remove sand, stone, nails, wire, etc. found within the working area. Foreign

objects may damage the cutting blades.

- Before commencing cutting, the cutting blades must have reached full working

speed.

- Always hold the Hedge Trimmer rmly with both hands on the handles only.

- The right hand grips the front handle.

- This is the way to safely operate the machine.

- Use a rm grip with thumbs and ngers encircling the handles.

- When you release the throttle, it takes a few moments before the cutting blades

stop.

- The Hedge Trimmer must not be used for cutting with fast idle. The cutting speed

cannot be adjusted with the throttle control in fast idle position.

- When cutting a hedge, the machine should be held so that the blades form a 15-

30° angle with the cutting line.

- If the Hedge Trimmer is used with circular movements against the edge of the

hedge, the twigs will be thrown directly to the ground.

- Pay special attention when cutting hedges which are laid out a long a wire-fence

and have grown through the fence.

- The blade must not contact the fence, otherwise the blades may be destroyed.

- Do not use the Hedge Trimmer continuously for a long time. It is normal to take a

break of 10 to 20 minutes after every 50 minutes operation.

- Should the cutting blades hit stones or other hard objects, immediately switch off

the engine and inspect the cutting blades for damage. Replace damaged blades

before re-commencing work.

- The engine must be switched off immediately in case of any engine problems.

- Operate the Hedge Trimmer with as little noise and contamination as possible. In

particular check the correct setting of the carburetor and the fuel/oil ratio.

- Do Not attempt to remove jammed cut material when blades are running. Put unit

down, turn it off, and remove necessary cuttings.

OPERATION OF THE MACHINE

Hedge surface to be trimmed

Trimming direction

15°-30°

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dolmar HT-2475 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info