Bedienungsanleitung Dolmar PM-461 (Seite 11 von 25) (Englisch, Holländisch)

507674

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

2. Push the mulching wedge into the deck. Lock the

mulching wedge with the button into the opening on

the deck. (Fig. 18, Fig. 19)

3. Lower the rear cover again.

TWO: Mowing with the grass catcher

1. For mowing with the grass catcher, remove the

mulching wedge and mount the grass catcher.

2. Removing the mulching wedge.

- Lift rear cover and remove the mulching wedge.

WARNING: Only with a stopped motor and

standstill cutter.

8. OPERATING INSTRUCTIONS

8-1 BEFORE STARTING

Service the engine with gasoline and oil as instructed in

the separate engine manual packed in your mower. Read

instructions carefully.

WARNING: Petrol is highly flammable.

Store fuel in containers specifically designed for this

purpose.

Refuel outdoors only, before starting the engine and do

not smoke while refueling or handling fuel.

Never remove the cap of the fuel tank or add petrol while

the engine is running or when the engine is hot.

If petrol is spilled, do not attempt to start the engine but

move the machine away from the area of spillage and

avoid creating any source of ignition until petrol vapors

have dissipated.

Replace all fuel tanks and container caps securely.

Before tipping the lawn mower to maintain the blade or

drain oil, remove fuel from tank.

WARNING: Never fill fuel tank indoors, with

engine running or until the engine has been allowed to

cool for at least 15 minutes after running.

8-2 TO START ENGINE AND ENGAGE

BLADE

1. The unit is equipped with a rubber boot over the end of

the spark plug, make certain the metal loop on the end

of the spark plug wire (inside the rubber boot) is

fastened securely over the metal tip on the spark plug.

2. Press the primer bulb 3-5 times before starting the

engine. (Fig. 20)

3. When starting cool engine, turn throttle choke lever to

“ ” position. When starting warm engine and

Operating, turn throttle choke lever to “ ” position.

(Fig. 21)

4. Standing behind the unit, grasp the stop control

handle and hold it against the upper handle as shown

in Fig. 22.

5. Grasp the starter handle as shown Fig. 22 and pull it

up rapidly. Return it slowly to the rope guide bolt after

engine starts. Release the stop control handle to stop

the engine and blade.

Start the engine carefully according to

instructions and with feet well away from the

blade.

Do not tilt the lawn mower when starting the

engine. Start the mower on a level surface, free

of high grass or obstacles.

Keep hands and feet away from the rotating

parts. Do not start the engine when standing in

front of the discharge opening.

8-3 OPERATION PROCEDURES

During operation, tightly hold the stop control handle with

both hands.

Note: During operation, when the stop control

handle is released, the engine will stop and thus stopping

the lawn mower from operating.

8-4 TO STOP ENGINE

CAUTION: The blade continues to rotate for a

few seconds after the engine is shut off.

1. Release the stop control handle to stop the engine

and blade.

2. Disconnect and ground the spark plug wire as

instructed in the separate engine manual to prevent

accidental starting while equipment is unattended.

8-5 FOR THE BEST RESULTS WHEN

MOWING

Clear lawn of debris. Be sure that the lawn is clear of

stones, sticks, wire or other foreign objects which could be

accidentally thrown out by the mower in any direction and

cause serious personal injury to the operator and others

as well as damage to property and surrounding objects.

Do not cut wet grass. For effective mowing do not cut wet

grass because it tends to stick to the underside of the

deck preventing proper mowing of the grass clippings. Cut

no more than 1/3 the length of the grass.

The recommended cut for mowing is 1/3 the length of the

grass. Ground speed will need to be adjusted so the

clippings can be dispersed evenly into the lawn. For

especially heavy cutting in thick grass it may be

necessary to use one of the slowest speeds in order to get

a clean well mowed cut. When mowing long grass you

may have to cut the lawn in two passes, lowering the

blade another 1/3 of the length for the second cut and

perhaps cutting in a different pattern than was used the

first time.

Overlapping the cut a little on each pass will also help to

clean up any stray clippings left on the lawn. The mower

should always be operated at full throttle to get the best

cut and allow it to do the most effective job of mowing.

Clean underside of deck.

Be certain to clean the underside of the cutting deck after

each use to avoid a build-up of grass, which would

prevent proper mulching.

Mowing leaves: The mowing of leaves can also be

beneficial to your lawn. When mowing leaves make sure

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dolmar PM-461 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info