Bedienungsanleitung Dolmar PS-400 (Seite 9 von 64) (Englisch, Französisch)

507618

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Important adjustments

WARNING!

At correct idle speed, chain should not turn. For di-

rections to adjust idle speed, see the appropriate

section of this instruction manual.

Do not use a saw with incorrect idle speed adjust-

ment. Adjust the idle speed yourself according to

the appropriate section of this manual.

Have your DOLMAR dealer check your saw and

make proper adjustments or repairs.

Check the saw chain tension frequently, especially

just after installing a new chain. New chains may

stretch more during their initial use. A properly

adjusted saw chain can be pulled freely around the

guide bar by hand without sagging. Always stop

the engine and wear gloves when checking or

adjusting the chain tension.

Working conditions

Operate your chain saw only outdoors. Operate the

saw under good visibility and daylight conditions only.

WARNING!

Take extreme care in wet and freezing weather

(rain, snow, ice). Put off the work when the weather

is windy, stormy or rainfall is heavy. Clear the area

where you are working.

WARNING!

Avoid stumbling on obstacles such as stumps,

roots or rocks and watch out for holes or ditches.

Be extremely cautious when working on slopes or

uneven ground. There is increased danger of slip-

ping on freshly debarked logs.

Cutting instructions

Always hold the saw firmly with both hands when the

engine is running. Place your left hand on the tubular

handle and your right hand on grip and throttle lever.

Left-handers should follow these instructions too.

WARNING!

Do not operate your chain saw in semi-throttle

position. Cutting in this position does not permit

the operator proper control of the saw or chain

speed.

WARNING!

Never come too close to a rotating chain with your

hands or body.

WARNING!

Do not cut any material other than wood or wooden

objects.

Use your chain saw for cutting only. It is not

designed for prying or shoveling away limbs, roots

or other objects.

When sawing, make sure that the saw chain does

not touch any foreign materials such as rocks,

nails and the like (fig. 8). Such objects may be flung

off, damage the saw chain or cause the saw to kick

back.

Wrap your fingers tightly around the handles, keeping

the handles cradled between your thumb and forefin-

ger (fig. 7). With your hands in this position, you can

best oppose and absorb the push, pull and kickback

forces of your saw without having it slip out of your grip

(see section of reactive forces). Make sure your chain

saw handle and grip are in good condition and free of

moisture, pitch, oil or grease.

Always start a cut with the chain running at full speed

and the spike bar in contact with the wood.

WARNING!

Never use the saw with one hand. You cannot

control reactive forces (see pages 10 to 12) and

may lose control of the saw.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dolmar PS-400 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dolmar PS-400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info