Bedienungsanleitung Dometic ECOVAC (Seite 8 von 16) (Englisch)

668118

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

7. Water leaking from rear of

toilet bowl.

8. Water is leaking from the

base/toilet connection.

9. Vacuum pump running too

often between flushes.

(See Vacuum Tester

Information on page 6.)

10. Vacuum pump will not

shut off.

11. Vacuum pump will not run.

12. Vacuum pump is running too

slow, overheating, blowing

fuses or circuit breaker.

a. Worn or defective vacuum breaker.

b. Loose vacuum breaker.

c. Cracked or defective toilet bowl.

a. Clamp ring my be loose.

b. Ball seals may be worn or defective.

a. Water leaks out of bowl between

flush ball and ball seal.

b. Vacuum line leak.

a. A vacuum leak exists.

b. Insufficient vacuum (pump creates

less than 10 inches Hg).

c. Faulty vacuum switch (pump

creates more than 10 inches Hg).

d. Improper wiring.

e. Bellows not pumping.

a. No electrical power.

b. Loose or broken electrical wiring.

c. Improper electrical connections.

d. Faulty vacuum switch.

e. Faulty motor.

f. Shut-down relay prevents pumping.

a. Gear motor is worn or defective.

b. Plugged vent line or vent filter.

c. Blockage in discharge line.

d. Improper wire size.

e. Improper voltage.

f. Vacuum pump bellows clogged

with tissue.

a. Remove vacuum breaker cover

and look into top of vacuum

breaker. Flush toilet. If water leaks

during flush, vacuum breaker

needs to be replaced.

b. Secure vacuum breaker connection.

c. Replace toilet bowl.

a. Remove plastic base cover (on

applicable models) and tighten the

clamp ring.

b. Replace ball seals.

a. Leave small amount of water in

bowl. If water is sucked from bowl,

see problems 1 and 2.

b. Tighten all connections at toilet,

vacuum generator or vacuum

holding tank (including hose

clamps and threaded spin nuts). If

leaks persists, contact SeaLand

Product Customer Service.

a. See problem 8b.

b. Isolate pump and use vacuum

gauge to check vacuum levels.

Could be a plugged discharge line

or worn duckbill valves.

c. Replace vacuum switch.

d. See wiring diagram to check for

proper wiring.

e. Tighten set screw in eccentric to

motor shaft. Otherwise, check for

damage to bellows and motor

shaft. Replace if necessary.

a. Check input power, circuit breaker

and fuse.

b. Tighten or reconnect wires at

vacuum pump and tank, vacuum

generator, or vacuum holding tank.

c. Be sure wires at vacuum switch

are connected to “B” terminals.

d. Check vacuum switch. Short across

“B” terminals with jumper wire.

e. Replace motor.

f. Empty the holding tank.

a. Check motor and replace if

necessary.

b. Disassemble and clean out vent

line. Replace vent filter if

necessary.

c. Disassemble and clean discharge

line. Be certain that in-line valves

(duckbill valves) and seacock are

in proper position.

d. Wire size too small. Check

electrical diagram for proper wire

size for voltage of pump used.

e. Check input power for low voltage.

f. Remove and clean bellows

assembly. (When flushing toilet,

use of more water may alleviate

this problem.)

Problem Possible Cause Service Instructions

TROUBLESHOOTING GUIDE (cont’d)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dometic ECOVAC Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info