Bedienungsanleitung Dometic Elite Control DX systems (Seite 5 von 24) (Englisch)

629513

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Elite Control Operations Manual Important Programming Notes To Installer And End User

L-2230 ENGLISH 3

IMPORTANT PROGRAMMING NOTES TO INSTALLER AND END USER

1. If your air conditioning unit is Cool Only (if it does not have a reversing valve), then you MUST select Cool Only Mode.

DO NOT select Automatic Mode for a Cool Only unit. If Automatic Mode is selected and the thermostat calls for heat,

the compressor will run. Since there is no reversing valve, the air conditioning unit will supply cool air when heating is

desired. Cool Only units do not heat. See “Modes of Operation” on page 5 for more information on how to set the

proper operating mode.

2. If your air conditioning unit has a Shaded-Pole (SP) fan motor instead of a Split-Capacitor (SC) High-Velocity (HV) fan

motor, you MUST program “SP” into parameter P-14 before operating the equipment. The SP units are recognizable

by an overhanging blower motor. (The SC motor of an HV unit is inside the blower, and the unit has “VTD” or “HV” in

the model number.) Only reprogram this parameter if you do NOT have an HV blower.

NORMAL HEATING OR COOLING CYCLE

In Automatic Mode, heating and cooling are supplied as required. If cooling is required, the system will start a cooling cycle

when the cabin temperature exceeds the set point by 2°F (1.1°C) and will continue to cool until the temperature equals the set

point. (See “P-23: Set Point Temperature Differential” on page 10 for instructions on how to reduce this variation to 1°F

[0.55°C].) The cabin temperature must drop below the set point by at least 4°F (2.2°C) in order for the system to switch from

cooling to heating. Similarly, if heating is required, the system will start a heating cycle when the cabin temperature is below the

set point by 2°F (1.1°C) and will continue to heat until the temperature equals the set point. The cabin temperature must exceed

the set point by at least 4°F (2.2°C) in order for the system to switch from heating to cooling.

If you select Cool Mode, only cooling is supplied. If you select Heat Mode, only heating is supplied. The cabin temperature in

either mode is maintained within 2°F (1.1°C) of set point by default. (See “P-23: Set Point Temperature Differential” on page 10

for instructions on how to reduce this variation to 1°F [0.55°C].) When the heating or cooling set point is satisfied, the

compressor cycles off and the fan returns to low speed. The fan speed remains constant if Manual Fan Speed is selected.

For more information on this feature, see “Modes of Operation” on page 5.

REVERSING VALVE OPERATION

The position of the reversing valve determines if the system is in Cool Mode or Heat Mode.

In addition, the reversing valve is programmed to toggle in these situations:

• When the system is running and heating or cooling is required, the reversing valve toggles to the opposite mode to

reduce the starting surge of the compressor.

• When a cooling or heating cycle is called for and if the system has been off for less than 75 seconds.

• When a cycle is interrupted from the display panel by pressing the Power button or changing the set point.

Unnecessary valve toggling is limited to reduce reversing valve noise. You can totally eliminate valve toggling by programming

the minimum compressor staging delay to 75 seconds or greater (see “P-3: Compressor Staging Time Delay” on page 8 for

more information).

Power-On Reset, which occurs when the system is powered up, always initiates a valve toggle.

INSTALLING THE DISPLAY PANEL

CHOOSING THE LOCATION

Before mounting the control panel, consider the location. The display panel’s built-in air sensor provides excellent room-air

temperature sensing when properly located and installed. For air sensor location see item 2 in Figure 1, page 2.

Mount the display panel on an inside wall, slightly higher than mid-height of the cabin, in a location with freely circulating air

where it can best sense average temperature. Its distance from the air conditioner must be within the 15’ (4.5m) length of the

display cable (custom lengths available).

Do not mount the display in direct sunlight, near any heat-producing appliances or in a bulkhead where temperatures radiating

from behind the panel may affect performance. Do not mount the display in the supply-air stream. Do not mount the display

above or below a supply-air or return-air grille. Do not mount the display behind a door, in a corner, under a stairwell or any

place where there is no freely circulating air.

If you can not mount the display in a suitable location for accurately sensing room temperature, install the optional remote air

sensor.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dometic Elite Control DX systems Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info