Bedienungsanleitung Dometic L-2230D Elite (Seite 5 von 28) (Englisch)

549152

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

English

L-2230 Operation

2.01 Operator Controls and

Display Panel

1-POWER BUTTON The Power Button is used to toggle

between the On and Off Modes. Press the Power Button

once to toggle the unit to the On Mode.

2-UP BUTTON Momentarily press and the set point will

appear in the display. Press and hold the Up Button the

set point will scroll to the upper limit. The set point

increases one degree each time the Up Button is

pressed and released.

3-DOWN BUTTON Momentarily press and release to

display the set point. The set point is decreased one

degree each time the Down Button is pressed and

released. Press and hold the Down Button and the set

point will scroll to the lower limit.

4-FAN BUTTON Press and release the Fan Button to

advance from auto fan to manual fan. Press and release

the Fan Button to advance the manual fan speeds, from

low to high. Press and release again to return to the

automatic Fan Mode. The selected Fan Mode is indi-

cated by the Auto and Manual Fan LEDs. The fan

operating mode can be changed from continuous (“con”)

to cycle-on-demand (“CYC”) by pressing and holding the

fan button for 5 seconds.

5-MODE BUTTON The Mode Button is used to select

one of the four operating modes. Press and release the

Mode Button and the Elite will advance to the next

mode. Continue to press and release the Mode Button

until the desired operating mode is reached. The mode

selected is indicated by the Mode LED, i.e., Cool, Heat,

Automatic or Moisture Mode.

6-THREE DIGIT SEVEN SEGMENT DISPLAY The inside

air temperature is displayed in the window whenever the

control is turned on.

The display also indicates program information, fault

codes and outside air temperature when the optional

outside air sensor is installed.

The display momentarily indicates the set point when the

Up or Down Button is pressed.

When the control resumes operation after a power

interruption all the Display LEDs will turn on for one

second. This is a normal operating condition and is

referred to as Power On Reset.

7-MANUAL INDICATION One of the three fan LEDs will

be lit when manual fan operation is selected.

8-AUTO FAN LED The Auto Fan LED is illuminated when

automatic fan speed operation has been selected.

9-AUTO MODE LED When the Auto LED is lit the unit

will automatically switch to heating or cooling when

required.

10-COOL MODE LED The Cool Mode LED will be lit

when Cool Mode is selected or the unit is in a cooling

cycle.

11-HEAT MODE LED The Heat Mode LED will be lit

when Heat Mode is selected or the unit is in a heating

cycle.

2.0 Elite Controls • Basic Operation

6-Display

2-Up

1-Power 3-Down

4-Fan

5-Mode

9-Auto Mode LED

10-Cool Mode LED

11-Heat Mode LED

12-Moisture Mode LED

8-Auto Fan LED

7-Manual Fan LEDs (high, medium, low)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dometic L-2230D Elite Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dometic L-2230D Elite

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info