Bedienungsanleitung Dometic rm 4401 (Seite 6 von 10) (Englisch)

342191

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

UILDING-IN

he refrigerator is intended for installation in a caravan or

otorhome, and the description relates to this application.

he refrigerator must not be exposed to radiated heat from

ot objects (e.g. below a cooker without proper heat

hielding).

xcessive heat irradiation impairs performance and leads to

ncreased energy consumption. For this reason the refrige-

ator should be installed if possible not at the entrance side

f the vehicle - normally orientated south and often with an

wning - which would impair the dispersion of heat and

ombustion gases from the ventilation openings.

t is not a good practice to install the refrigerator so that the

ent openings are covered by the vehicle's entrance door

hen this is open. This would reduce the ventilation air flow

o the cooling unit and reduce refrigeration performance.

he enclosure

he refrigerator must be installed in an enclosure, the

imensions of which are shown in TECHNICAL DATA.

he bottom of the enclosure must be horizontal and even

o that the refrigerator can be easily pushed into place. It

ust be sturdy enough to carry the wieght of the refrigera-

or.

attens must be installed at the enclosure and fitted with

ealing strips, as shown in fig. 4.

lide in the refrigerator until it is flush with the front of the

ecess. There must be 10-20 mm free space behind the

efrigerator.

our fasteners are fitted in plastic bushings in the side walls

f the fridge, fig. 7. They are used for securing the refrigera-

or in the enclosure.

he side walls of the enclosure and/or any wooden braces

nstalled to hold the refrigerator must be dimensioned to

eat the screws securely, also considering the forces due to

he movement of the vehicle.

ith the refrigerator in place, drive the screws through the

ushings in the lining of the refrigerator into the walls of the

nclosure (fig.7). There must not be more than 3mm of

learance between refrigerator and enclosure on each side.

f necessary, wooden strips or similar should be fitted.

ote: This is the only approved means of securing the

efrigerator to the enclosure and to the vehicle. Faste-

ers penetrating other parts of the insulation (PU) foam

f the refrigerator might damage components like elec-

ric wiring etc.

ENTILATION OF THE UNIT

t high ambient temperatures the refrigeration unit will only

erform adequately when properly ventilated.

he refrigeration unit is ventilated via two openings in the

all of the caravan (see fig. 5). Fresh air enters through the

ower opening and warm air is discharged through the upper

ne.

ocate the lower opening immediately above the floor of the

ecess, and the upper one as high as possible above the

ondenser (C) of the refrigeration unit, at least as shown in

ig. 6b but preferably as shown in fig. 6a.

entilation grilles Fig. 2

he openings in the caravan wall must be fitted with

lectrolux ventilation systems.

itting the grilles, model A 1620, which were specially

eveloped by Electrolux for this purpose (shown as D in fig.

). It is a good idea, to install the frame R 1640 (A in the

ame figure), at the same time. Then the grilles can be

asily removed which permits inspection and small repairs

o be carried out without the necessity for removing the

efrigerator from the recess.

f there is no outer grille at floor level where leaking gas can

scape, a 40 mm hole to the outside should be made in the

loor of the recess to drain any unburnt gas to the outside

as.

it the hole with wire mesh and an angled plate to protect

rom stones, mud etc.

emoval of flue gases

he ventilation passage at the rear of the recess, between

he outer wall of the vehicle and the refrigerator (fig. 6), is

ealed off against the living space, and so cold draughts are

xcluded (winter camping) and no flue gases can penetrate

nto the vehicle. Thus a special flue outlet is no longer

ecessary - the gases are dispersed through the upper vent

rille.

ote: With this mode of installation the same type of grilles

(

without an integrated flue outlet), should be installed at the

pper as well as at the lower vent open-ning. The angled

-piece for the flue tube (when delivered) should not be

sed in this case.

he top of the enclosure above the flue tube (I), fig. 6,

hould be covered with aluminum sheet metal, as indicated

n (B), to facilitate the heat dispersion.

n fig. 6 the letters have the following meaning:

A. Frame R 1640 for the grilles

B. Aluminum cladding

C. Condenser of cooling unit

D. Vent grill A 1620

E. Sealing profile (optional extra)

Width 486 mm, Electrolux art. nr. 295 1147-10

F. Refrigerator rear wall

G. Wooden batten approx. 10 x 20 mm (see fig. 4)

H. Height of the enclosure (see TECHNICAL DATA)

I. Flue tube

P GAS CONNECTION

he refrigerator is designed for operation on LP gas of

utane type the pressure of which must be 28 mbar for

utane and 37 mbar for Propane. Check that this is stated

n the data plate.

he refrigerator is not designed for operation on town gas or

atural gas.

CAUTION! CHECK THAT THE GAS SUPPLIED TO THE

REFRIGERATOR IS AT THE CORRECT PRESSURE.

SEE THE REDUCING VALVE ON THE LP GAS

CONTAINER

Dometic rm 4401 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dometic rm 4401

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info