610380
59
Zoom out
Zoom in
Vorherige Seite
1/323
Nächste Seite
28
flashing +
acoustic
signal 20 s
Check burner, burner nozzles, if necessary contact
Customer Service and arrange replacement
Burner defective or coo-
ling unit defective
7
3
4.21 Information on failure display
and trouble-shooting
4.21.1 Status indicators
Operation with on-board 12 V power supply
Indicator
Fault
Remedy
flashing +
acoustic signal
20 s
Check mains power connection, mains voltage, fuse230V mode: "230V" not
available or voltage too
low
1 2 3 4 5 6 8
7
= Button ON / OFF
= Energy selector switch 230V AC
= Energy selector switch GAS
= Energy selector switch 12V DC
2
1
3
4
= selector switch "AUTOMATIC"
= temperature level button
= temperature level display
= fault LED / GAS FAULT reset button
6
5
7
8
8
2
flashing +
acoustic signal
20 s
Arrange replacement of 230V heating element,
contact Customer Service
230V mode: 230V hea-
ting element defective
7
2
flashing
contact Customer ServiceTemperature sensor
without contact or
defective
7
flashing +
acoustic signal
20 s
Arrange replacement of 12V heating element,
contact Customer Service
12V mode: 12V heating
element defective
7
4
flashing +
acoustic signal
20 s
Check 12 V connection, on-board battery, fuse
AES: Check D+ signal
12V mode: "12 V" not
available or voltage too
low
8
4
flashing +
acoustic signal
20 s
GAS/Automatic mode:
Flame not ignited
8
3
Check gas supply (gas bottle, gas valve)
Press the (8) button after clearing the fault.
Acoustic signal,
15 s, at 2 minute
intervals
Interior lighting is swit-
ched on
Close door, check door contact
Refrigerator operation
Before notifying the authorised Service Center,
please check whether:
n the instructions in section "Operating the
refrigerator" have been observed.
n the refrigerator stands level.
n it is possible to operate the refrigerator with
any available power source.
MES
AES
Fig. 52
n Refrigerators with an electronics system
(MES, AES) indicate the occurence of a
malfunction by the LED or display flashing.
n If a malfunction occurs, the indicator LED
"Failure" (8) flashes simultaneously. In the
case of AES models an acoustic alarm
sounds.
Fig. 51
1 2 3 4 6 7 8
59

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Dometic RMS 8461 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Dometic RMS 8461

Dometic RMS 8461 Installationsanweisung - Englisch - 28 seiten

Dometic RMS 8461 Installationsanweisung - Holländisch, Französisch - 72 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info