773928
27
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
27
DO7347H
www.domo-elektro.be
EN
USE
Before you use the appliance: plug in the appliance and turn on the on/o switch at the back of the device.
The display displays the symbol and emits an audible signal to indicate that the device is in standby
mode. You can set the appliance using the control panel, but also using the remote control. You can make
the settings in the same way. The display will show you the selected settings. Each time a button is
pressed, the device emits an audible signal to indicate that the user is making a setting or adjustment.
ON/OFF SWITCH
Push the on/o switch to turn on or o the appliance. “HI” and the symbol appear on the display when
the device is switched on. This means the device is at its highest power setting. If you switch o the
device, the display will count down from 15 to 0 in order to cool itself down.
Note: when the device is switched o via this button, the device goes into standby mode. This means it is
not completely disabled. You can only switch the device o completely via the on/o switch on the back
of the device.
FUNCTION BUTTON
1. Press the button once: low power (1200 W): “LO” appears on the display, the device is now operating
at its lowest power setting.
2. Press the button a second time: ECO: the symbol appears on the display. You can set the
temperature between 5-35 °C as desired using the buttons to increase and to decrease . You
can also keep this button pressed until you reach the desired setting. If the ambient temperature is 2
°C higher than the set temperature, the device switches to standby mode. If the temperature falls
back below the set temperature, the eco function switches on again. This is the most energy-
ecient way to maintain the temperature.
Note: the device remembers the last temperature setting made. This means that when you switch
the device on again, the last temperature setting appears on the display when eco mode has been
selected.
3. Press the button for a third time: high power (2000 W): “HI” appears on the display, the device is
now operating at its highest power setting.
TIMER
1. Push this button to set the timer. The symbol appears on the display.
2. You can set this between 1-8 hours using the buttons to increase and to decrease . You can
also press and hold this button until you reach the desired setting.
3. When the selected time has been expired, the appliance will enter the stand-by mode and will no
longer emit heat.
Note: if the device is in stand-by mode, you can set the timer. After the set time has elapsed, the device
switches itself on automatically and will operate at its highest power setting.
OSCILLATION
Press the oscillation button to allow the heater to oscillate the air from left to right and vice versa. Press
this button again to stop this. If you switch the device o with the on/o button, this function stops even
if you have not pressed the oscillation button.
27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Domo DO7347H wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info