Bedienungsanleitung Dovre 2510SD (Seite 55 von 253) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

571606

Zoom out

Zoom in

Vorherige Seite

1/253

Nächste Seite

The opening direction of the door can be changed.

The appliance is supplied with a door turning to the

right. An optional locking rod is required for a left-

turning door (supplied separately). The instructions

for changing the door swing direction are provided

with this locking rod.

The appliance is supplied with a connecting kit for

the outside air supply.

The appliance is not suitable for continuous use.

The insert fireplace has an integrated convection

system. This means that when installing the appli-

ance it is not necessary for a separate convection

space to be built and the use of air inlet and outlet

grates for convection is not necessary.

The space between the cast-iron fireplace and

steel convection box serves as the convection

space. Surrounding air is drawn in at the bot-

tom of the appliance. The air is directed to the

fireplace where it is heated. The heated air then

leaves the front side of the convection space

through the air opening on the upper side of the

fireplace.

The appliance is equipped with two additional con-

nections in order to transport convection heat to

other areas.

The appliance is equipped with two built-in fans

that aid convection. The turning speed of the fans

can be adjusted using a speed control. This speed

control is supplied with the appliance. The fan and

speed control are connected to the mains electric

circuit; see paragraph "Connecting fan to the

mains".

The fan works thermostatically. That means

that the fan only starts to operate if the

insert fireplace is sufficiently warm and the

fan switches off once the insert fireplace

has cooled sufficiently.

The appliance can be supplied with an outer frame

to which you can attach a decorative frame. The

decorative frame is supplied as an option.

Installation

Preparation

Please check the appliance for damage caused dur-

ing transport or any damage or defects immediately

after delivery.

If you detect damage caused during transport

or any other damage or defects, do not use the

appliance and notify the supplier.

Remove the removable parts (fire-resistant inner

plates, fire compartment, fire basket, ash removal

port and ash pan) from the appliance before you

start installing the appliance.

By removing removable parts, it is easier to

move the appliance and to avoid damage.

Note the location of the removable parts, so

that you can re-position the parts in the correct

place later on.

1. Open the stove door.

2. Remove the fire-resistant inner plates.

Cast iron inner plates protect the combustion

chamber and dissipate heat to the sur-

roundings.

Fitting the handle

The appliance is supplied with a loose handle, the so-

called "cold hand".

The form of the “cold hand” depends on the model of

the appliance.

Fit the wooden handle to the adaptor using screw

M8x50 provided; see following figure.

09-20015.088

See the next figure for opening the door.

Subject to change because of technical improvements

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dovre 2510SD Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info