Bedienungsanleitung Dovre 2520S2R (Seite 53 von 253) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

571614

Zoom out

Zoom in

Vorherige Seite

1/253

Nächste Seite

The flue or chimney must be airtight and well-

cleaned and guarantee sufficient draught.

A draught/vacuum of 15-20Pa during normal

operation is ideal.

Starting from the flue spigot, the flue must run as

vertically as possible. Changes in direction and

horizontal pieces disrupt the outward flow of com-

bustion gases and may cause soot deposits.

To prevent combustion gases from cooling down

too much, which reduces the draught, ensure that

the interior diameter is not too big.

The flue or chimney should ideally have the same

diameter as the connection collar.

For the nominal diameter: see the appendix

"Technical data". If the smoke channel is well

insulated, the diameter may be slightly bigger

(up to 2x the section of the connection collar).

The section (area ) of the smoke channel must be

constant. Wider segments and (in particular) nar-

rower segments disrupt the outward flow of com-

bustion gases.

When using a cover plate or exhaust hood : make

sure that the cover does not restrict the flue outlet

and that the cap does not impede the outward flow

of combustion gases.

The flue must end in a zone that is not affected by

surrounding buildings, trees or other obstacles.

The flue outside the house must be insulated.

The chimney must be at least 4metres high.

As a rule of thumb: 60cm above the ridge of the

roof.

If the ridge of the roof is more than 3metres away

from the flue: stick to the measurements in the fol-

lowing figure. A = the highest point of the roof

within a distance of 3metres.

Ventilation of the area

For good combustion, the stove needs air (oxygen).

This air is supplied via adjustable air inlets from the

area in which the stove is installed.

The combustion will be incomplete in case of

insufficient ventilation, which results in toxic

gases being produced and spread through the

area.

As a rule of thumb, the air supply should be

5,5cm²/kW. Extra ventilation is needed when:

The stove is in an area that is well-insulated.

There is mechanical ventilation, for example a cent-

ral extraction system or an extraction hood in an

open kitchen.

You can provide extra ventilation by having a vent-

ilation louvre fitted on the outside wall.

Make sure that other air consuming appliances (such

as tumble-driers, other heating appliances or a bath-

room fan) have their own supply of outside air, or are

switched off when you use the appliance.

Floor and walls

The floor on which the appliance is placed must have

sufficient bearing capacity. The weight of the appli-

ance is given in the appendix “Technical Data

appendix”.

There may not be any electrical wires in the

floor below the appliance and in the walls

around it.

Subject to change because of technical improvements

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dovre 2520S2R Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info