Bedienungsanleitung Dovre 2620SC-B (Seite 58 von 253) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

571616

Zoom out

Zoom in

Vorherige Seite

1/253

Nächste Seite

intense trial fire with newspaper and dry, small

kindling.

If there is new masonry then wait until the

masonry has dried sufficiently.

Drawing off convection air

The appliance is equipped with two additional con-

nections in order to transport convection heat to other

areas.There must be air grids in these areas. If you

wish to make use of this function, proceed as follows:

1. Remove the two push-out plates on top of the con-

vection box by tapping them loose with a hammer.

2. Fit the two connection collars supplied with a dia-

meter of 125 mm on the resulting openings using

the M8x16 screws and M8 bolts supplied.

3. Connect flexible tubing with a diameter of 125 mm

and route them to the desired areas.

4. Connect the flexible tubing to the outlet grates in

the rooms.

Building the new hearth

Inside the hearth you provide space for convection. In

this space the air must be able to move freely. It must

be possible for air to be sucked in for combustion, and

the air heated by the fireplace (the convection air)

must be able to flow freely into the area to be heated;

see next figure.

When building the hearth, follow these instruc-

tions:

The top of the hearth must be closed airtight using

a cover plate of incombustible and heat-resistant

material.

The cover plate must be level and placed at least

30 cm below the flue opening in the ceiling.

If desired, an additional outlet grate can be fitted at

the top of the hearth, just below the cover plate.

Do not use combustible material in the hearth

space and prevent thermal bridging by using

materials that conduct heat.

Follow the instruction below when building the

hearth:

1. Lay the floor of the hearth.

Make sure the door of the appliance can swing

freely over the hearth floor.

2. Build the hearth up to the smoke dome.

Ensure that a clearance of 2 mm is maintained

between the appliance and the masonry to

accommodate the thermal expansion of the fire-

place.

3. The inside of the hearth may, if desired, be clad-

ded with reflective, insulating material.

Additional cladding of the built-in space pre-

vents unnecessary thermal radiation to outer

walls and/or adjacent rooms. It also prevents

damage to the hearth wall insulation.

4. Build the rest of the hearth up to the flue opening

hole in the ceiling.

The masonry should not rest on the fireplace.

Use a support such as a steel beam. Leave a

clearance of at least 3 mm between the sup-

port and the appliance.

5. Close the built-in space with the cover plate.

6. Put an air grate below the cover plate to allow for

the ventilation of the appliance.

7. Make an opening above the cover plate in order to

prevent any pressure build-up.

The figure below provides an example of the placing of

a fireplace insert in a hearth which is done using the

instructions given above.

Subject to change because of technical improvements

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dovre 2620SC-B Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info