Bedienungsanleitung Dovre Sense 113 (Seite 61 von 291) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Norwegisch)

695928

Zoom out

Zoom in

Vorherige Seite

1/291

Nächste Seite

kettle directly onto an enamelled stove; use a stand to

prevent damage. Attention: Do not allow aggressive

acidic products to get onto enamelled components.

Lubrication

Although cast-iron is slightly self-lubricating, you will

still need to lubricate moving parts frequently.

Lubricate the moving parts (such as guide sys-

tems,hinge pins, latches and air slides) with heat

resistant grease that is available in the specialist

trade.

Touching up damaged paint

Small areas of damaged paint finish can be touched-

up with a spray can of special heat-resistant paint,

available from your supplier.

Touching up the enamelled surface

Enamelling is a process carried out by traditional meth-

ods, meaning that it is possible that small colour dif-

ferences and damage may occur. The appliances

undergo a visual inspection in the factory, that is to

say, the inspector looks at the surface for a period of

10 seconds from a distance of 1 metre.

Any damage that does not stand out is regarded as

OK. A special heat-resistant paint is supplied with the

appliance to touch up any minor damage caused dur-

ing transport.

Apply the heat-resistant paint in thin layers and leave

to dry well before using the appliance.

Some enamel colours are temperature-sensitive. It

can happen that the colour changes during use.

The original colour will return after the appliance

has cooled down.

If enamelled surfaces become very hot, hairline

cracks can occur. This is a normal phenomenon

and has no impact on the functioning of the stove.

Ensure that the stove is not overburdened. If it

does become overburdened then the surface

gets very hot possibly resulting in lasting dam-

age to the enamel.

Checking the seal

Check whether the door sealing rope is still in good

condition and works well. The sealing rope is

subject to wear and will need to be replaced over

time.

Check the appliance for air leaks. Close any

chinks with stove sealant.

Allow the sealant to harden fully before lighting

the appliance, as any moisture in the sealant

will form bubbles, resulting in a new air leak.

Adjust door closing

Check if the door closes properly. If required, the clos-

ing of the door can be set looser or tighter by adjusting

the distance between the locking cam and the door.

Proceed as follows:

1. Open the door. The locking cam (2) is now freely

accessible; see next figure.

2. Unscrew the two screws (1) with which the lock-

ing cam is attached.

3. By removing the packing plate (3) behind the lock-

ing cam (2), the door closes more tightly. If the

door closes too tightly then insert an additional

packing plate behind the locking cam.

4. Tighten the two screws and check the closing of

the door once again.

09-20021-024

123

Replacing the glass

If the glass in the appliance is broken or

cracked, it must be replaced before the stove

Subject to change because of technical improvements

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dovre Sense 113 Seite 61

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info