Bedienungsanleitung Dovre Sense 203GA (Seite 53 von 204) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

745853

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

Subject to change because of technical improvements

7. Finish the seam between the pipe and the cone of

the roof sheet or lead slab watertight with silicon

sealant and if necessary a storm collar (5).

8. Install the roof sleeve (6) and secure it with the

clamping strap included in the delivery.

Establishing a gas connection

The connection to the gas pipe is on the back of the

gas regulator block, which is at the bottom right of the

stove.

The connection must meet the following conditions :

A coloured gas valve must be inserted in the gas

supply pipe, as close to the stove as possible and

always accessible.

The connection must be voltage-free.

Have a certified installer make the connection.

Follow the instructions below:

1. Check whether the type of gas and gas pressure

on site correspond with those marked on the type

plate.

The type plate is located on the appliance.

2. Assemble the gas supply pipe. 3/8” G pipe or cop-

per pipe with diameter 10/12 mm suffices for pipes

up to +/- 10 m. 1/2” G pipe or copper pipe with dia-

meter 13/15 mm is used for lengths exceeding 10

3. Install the gas valve.

4. Connect the stove to the gas supply pipe. The gas

connection can be made using the opening on the

back. Use a 3/8” coupling to do this.

5. Check if the supply pipe is gastight (using soapy

water, for example).

Installing the remote control

set

The Mertik Maxitrol GV60 remote control set consists

of a handset (transmitter) and a receiver. The system

works on batteries; connecting an AC adaptor is

optional.

The batteries (2 x 1.5 Volt AAA for the handset

(transmitter), 4 x 1.5 Volt AA for the receiver)

are included.

Use only the Mertik Maxitrol AC adaptor or an

adaptor preapproved by Mertik Maxitrol. Other

adapters probably do not suit your system

and/or can damage it.

Batteries – handset (transmitter)

▪ 2x 1.5 Volt AAA (LR 03) (recommended quality:

alkaline).

▪ Handsets with display: Battery indicator on the dis-

play.

▪ We recommend that you replace the battery after 2

years.

Batteries – receiver

▪ 4x1.5 V AA (recommended quality: alkaline)

▪ indicator light Battery nearly empty: beeps regularly

for 3 seconds if the motor is running.

▪ An AC adaptor may have to be used instead of bat-

teries.

Insert the batteries in the transmitter (handset) and

in the receiver (black box, lid can be opened eas-

ily).

The receiver is located on the left in the base of the

appliance, behind the hatch in the base; see the fol-

lowing figure.

09-20021-414

Programming the electronics code

Codes selected from approximately 65,000 randomly

available codes are automatically assigned to all Mer-

tik Maxitrol electronics. This code is assigned to the

handset for the remote control set. The receiver must

read this code from the handset.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dovre Sense 203GA Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info