Bedienungsanleitung Dovre VIRTUS 50 GA (Seite 55 von 215) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

745854

Zoom out

Zoom in

Vorherige Seite

1/215

Nächste Seite

DOVRE

Subject to change because of technical improvements

Roof sleeve through a pitched roof

of flammable material

Read the "Installation Conditions" chapter care-

fully and follow the installation instructions

below.

1. Start at the stove and add the concentric pipes

one at a time, including the changes in direction

you want, along the route you decided on in

advance, up to just under the roof.

2. Decide on the location for the roof sleeve.

3. Make an elliptical hole so that a fire separation of

at least 50 mm remains round the pipe.

4. Extend the concentric pipe (1) until it extends at

least 250 mm above the roof surface (more is per-

mitted up to a maximum of 1000 mm stand-alone);

see next figure.

5. Center the pipe using the centering plates (2) and

attach it with the installation bracket (3).

6. Slide a roofing sheet for pitched roof (tar roof) or a

lead slab (4) (tile roof) over the pipe and seal or

cover it watertight.

7. Finish the seam between the pipe and the cone of

the roof sheet or lead slab watertight with silicon

sealant and if necessary a storm collar (5).

8. Install the roof sleeve (6) and secure it with the

clamping strap included in the delivery.

Establishing a gas connection

The connection to the gas pipe is on the back of the

gas regulator block, which is at the bottom right of the

stove.

The connection must meet the following conditions :

A coloured gas valve must be inserted in the gas

supply pipe, as close to the stove as possible and

always accessible.

The connection must be voltage-free.

Have a certified installer make the connection.

Follow the instructions below:

1. Check whether the type of gas and gas pressure

on site correspond with those marked on the type

plate.

The type plate is located on the appliance.

2. Assemble the gas supply pipe. 3/8” G pipe or cop-

per pipe with diameter 10/12 mm suffices for pipes

up to +/- 10 m. 1/2” G pipe or copper pipe with dia-

meter 13/15 mm is used for lengths exceeding 10

3. Install the gas valve.

4. Connect the stove to the gas supply pipe. The gas

connection can be made using the opening on the

back. Use a 3/8” coupling to do this.

5. Check if the supply pipe is gastight (using soapy

water, for example).

Installing the remote control

set

The Mertik Maxitrol GV60 remote control set consists

of a handset (transmitter) and a receiver. The system

works on batteries; connecting an AC adaptor is

optional.

The batteries (2 x 1.5 Volt AAA for the handset

(transmitter), 4 x 1.5 Volt AA for the receiver)

are included.

Use only the Mertik Maxitrol AC adaptor or an

adaptor preapproved by Mertik Maxitrol. Other

adapters probably do not suit your system

and/or can damage it.

Batteries – handset (transmitter)

l 2 x 1.5V AAA (LR 03) (recommended quality:

alkaline).

l Handsets with display: Battery indicator on the dis-

play.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dovre VIRTUS 50 GA Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info