Bedienungsanleitung Dovre VISTA 900 (Seite 52 von 261) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Norwegisch)

813296

Zoom out

Zoom in

Vorherige Seite

1/261

Nächste Seite

16 Subject to change because of technical improvements

Prepare

connection to outside air

If the appliance is installed in a room with insufficient

ventilation, you can install the outside air connecting

kit to the appliance.

09-20021-130

The outside air collar can be assembled on the outside

depending on how the fireplace is built in, see position

2 in the figure above. If the method of building in and

the connection of the outside air requires the outside

air collar to be assembled through the inside, first

remove the inner plates and the fire compartment

base. Then remove the air distribution housing, see

position 1 in the figure above. Disassemble the con-

necting collar for the outside air, connect it airtight to

the flexible hose for the outside air, assemble the con-

necting collar through the inside of the appliance and

assemble the air distribution housing.

Make sure that the seals are not damaged. If

they are damaged the seals must be replaced.

Make sure that the air distribution housing is

connected airtight and that the working of the

air slide valve is not impeded.

The air supply tube is 100mm in diameter. If the tube

is smooth, it may be no longer than 12metres. If

accessories such as bends are used, the maximum

length (12m) must be reduced by 1m for each access-

ory used.

Outside air intake duct through the

wall or the floor and the connection

collar

1. Make a hole in the wall or the floor (refer to

Appendix 2, "Dimensions" for a suitable position

of the hole).

2. Close the air connection tubehermetically on the

wall.

Building into a new hearth

The fireplace insert is installed in two stages:

Placing and connecting the fireplace

Building up the hearth around the fireplace.

Placing and connecting the fire-

place insert

1. Place the appliance at the right height, flat and

level.

2. Make sure there is sufficient space between the

existing walls (insulated as per instructions) and

the rear of the appliance.

3. Connect the appliance to the flue hermetically.

4. Check the draught in the flue and the seal of the

connection on the flue gas duct by making a small,

intense trial fire with newspaper and dry, small

kindling.

Wait until new masonry has dried sufficiently.

5. For outside air supply connection: connect the out-

side air supply to the connection kit you fitted to

the appliance.

Building the fireplace

Inside the hearth you provide space for convection. In

this space the air must be able to move freely. It must

be possible for air to be drawn in for combustion pur-

poses, and the air heated by the built-in fireplace (the

convection air) must be able to flow freely within the

space to be heated; see following figure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dovre VISTA 900 Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info