Bedienungsanleitung Dr. Kern excellent 24 7 (Seite 24 von 28) (Deutsch, Englisch)

499398

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

english

Ventilation of the Solarium

The ventilation system employed in your new solari-

um is the best possible. Cool air is drawn into vents at

the base of the unit.

The strongest ventilation is at the bench acrylic area.

With the strong air circulation, dust will be carried into

the solarium and deposited onto its internal

components. Any accumulation of dust will hinder the

ventilation efficiency of the main fans. For this reason

the solarium should be cleaned on a regular basis.

Bear in mind that cool air can reduce the temperature

of this machine better than warm air. Insure that the

room in which the solarium is operated is sufficiently

supplied with cool, fresh air.

Cleaning the Solarium

Disconnect the power from the machine before each

cleaning. Use only a moist cloth during cleaning.

Cleaning of the Acrylic Glass Sheets

Under heavy air circulation, as described above, dust may

collect on the inner sides of the acrylic glass sheets. This

may occur all over the sheets or at localised areas. In this

case, the acrylic glass sheet must be removed and

cleaned, as described above under "Replacing the lamps".

Use only solvent-free, non-aggressive household

cleaning agents for cleaning the glass sheets.

Such dust contamination can also occur with new units

after only a short time in operation. This is due to the varying

static charging of the acrylic glass sheets.

This cleaning work is not covered by the guarantee

conditions.

Facial lamps operate at very high temperatures and

are cooled with fans in the cassettes. The lamp function

is controlled additionally by a heat sensor. Should a

fan stop working in any cassette the relay will turn the

unit off automatically. The face tanner may not be used

until an authorised service representative has repaired

the problem. Automatic emergency shut offs of this

type occur rarely. The cassette fans in the facial tanners

rarely fail.

Only factory - original components and spare parts

may be used in servicing this solarium.

The filter and lower safety plate can be removed from the

cassette for cleaning, see Fig. 38. When refitting the plate,

always ensure that the filter plate is inserted facing upward,

i.e. toward the face-tanner. To ensure this is done correctly,

you should mark the plate accordingly when removing it,

and then refit it in the same way.

To change the metal halogen lamp, grasp the lamp at one

of the flattened ends, and push approximately in the

lengthwise direction in order to remove it from the holder,

see Fig. 39.

The new lamp is inserted in the same way. Ensure that

you do not touch the actual glass of the lamp. Any marks

or fingerprints on the lamp should be cleaned off with

pure alcohol or white spirit.

NEVER USE A FACE TANNER WITH BROKEN OR

CRACKED FILTER GLASSES! Doing so will cause

damage to eyes and facial skin.

Fig. 38

Remove these 2

screws

Fig. 39

Thermal fuse

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dr. Kern excellent 24 7 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info