Bedienungsanleitung Drayton DIGISTAT plus RF (Seite 7 von 24) (Englisch)

653292

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Client Drayton File Name 7342 Drayton Amends LP20RF 06515085001 ISSB

Artworker -

Proof Stage

Finished Size A5 148x210mm

Creative Director Mike Lane Artwork % 100%

Modification Date 19/03/15 9:21AM Bleed 3mm

Installation Guide LP20RF & DIGISTAT+RF

CLOCK?

6:30

10:30

OFF

Before fixing the Digistat+RF to the wall it is recommended

to first check the signal strength from that location.

To do this, after initial start up, the colon, CH and antenna

symbols should be ashing on the LP20RF display.

1.

Press the set? button 4 times.

2.

Press the OK button once.

3.

Press the set? button 4 times; Lrn and OFF should

be displayed.

4.

Press the + button so the display shows ON and a

ashing antenna symbol. The learn mode is now

ready to receive a signal from the transmitter

during the next two minutes.

5.

Take the Digistat+RF unit and stand near the boiler.

6.

Remove the battery cover and t the batteries.

7.

The symbols on the receiver will stop ashing and

the display will show ‘SSI, Antenna and ON’.

8.

Press ‘SET’ on the receiver and the display will

show ‘SSI and Antenna’.

CLOCK?

6:30

10:30

OFF

CLOCK?

6:30

10:30

OFF

CLOCK?

6:30

10:30

OFF

9.

After a few seconds the display will show ‘- - -’.

Remove the batteries from the Digistat+RF, press

and hold the ‘set’ button whilst retting the

batteries, keep the ‘set’ button held and after a few

seconds the display will show ‘rF’ which indicates

that the Digistat+RF is continuously sending a

signal to the LP20RF (receiver).

The receiver display will now show the ‘learnt’

transmitter code and the antenna’ as well as the

signal strength as indicated by the chevrons on the

right hand side of the display.

J 

Place the transmitter in the desired nal position

and return to the boiler to check the receiver

display. The ideal transmitter position will result

in the receiver display showing 4 chevrons and the

LED will be green.

K 

If the LED is red or no LED is showing and the

display indicates 1 or 2 chevrons, the transmitter

will need to be re-positioned until the LED

changes to amber or green and 3 or 4 chevrons are

indicated on the display.



NOTE:

If there is no LED and the display shows ‘- - -’, there

is no signal being received at all from the transmitter.

Transmission will resume once the transmitter is re-

positioned in a part of the house where an amber or

green LED and 3 or 4 chevrons are achieved.

L 

Once you are happy that, when in the desired

location, the transmitter is sending a good signal

to the receiver i.e. amber or green and 3 or 4

chevrons, the transmitter can be xed to the wall.

CLOCK?

6:30

10:30

OFF

LED Indication Chevrons RF Strength

Green 4 Very strong

Amber 3 Strong

Red 2 Weak

None 1 Very weak

Signal strength

indicators

Transmitter code

(may be different)

LED indicator shows different colour depending

on signal strength (see table below)

Wireless Commissioning

& Signal Strength

5LP 20R F & DI GI STAT+R F

06515085001 ISSB

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Drayton DIGISTAT plus RF Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info