Bedienungsanleitung Drayton Erie Digistat RF2 (Seite 2 von 2) (Englisch)

38153

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Digistat RF2

Once the ‘wireless system’ has been commis-

sioned, the unit will display the actual room

temperature and the time at somewhere after

12.00 midnight (Diagram A).

Note: If this unit has replaced a standard

room thermostat and/or a programmer is

incorporated in the control system, it is

suggested that the central heating (CH) channel

is switched to ON/CONT/24HRS. Operation

of the heating times and temperatures will be

controlled by this unit.

Diagram A Diagram B

Digistat RF2 has an indicator to show when the heating system is ON or OFF,

e.g. if the SET temperature is 20°C and the actual room temperature is below

20°C a flame symbol will appear on the display (Diagram B). This indicates a

demand for heat (system will switch ON).

During normal operation, the Digistat RF2 will display actual room

temperature continuously.

SETTING THE TIME OF DAY (steps 1-4)

The diagram next to each step description shows resulting display.

1. Press “SET?” button

2. Press “Yes” (–) button. The hours will flash as shown

here. Use the + and – buttons to set correct hour.

3. Press “SET?” button again and the minutes will flash, use

+ and – buttons to set correct minute time.

4. Press “SET?” button twice to return to normal operating

mode.

PRE-PROGRAMMED TIMES AND TEMPERATURES

The Digistat RF2 comes with the following preset programme.

Symbol Setting Time Temperature

1st day time 6.30 20°C

2nd day time 8.30 16°C

3rd day time 4.30 pm 21°C

Night time 10.30 pm 7°C*

* 16°C if selector pin removed, see installation instructions

TO VIEW OR CHANGE THE FACTORY SETTINGS (

steps 5-10)

5. Press the “SET?” button until this display is shown.

ress the Yes (–) button again. This tells you that at 6.30,

he heating system will control your home at 20°C. If you

ish to alter the temperature use the + and – buttons.

ress the “SET?” button. The time will now flash. If you

ish to alter the switching time use the + and – buttons.

This will change the switching time in 10 minute steps.

8. Press the “SET?” button, this tells you that at 8.30, the

heating system will control your home at 16°C. If you

wish to alter this temperature use the + and – buttons.

9. Continue to press the “SET?” button as in steps 6 and 7

above to advance through the times and temperatures. If

you wish to alter any of the times and temperatures use

the + and – button, when the one you wish to alter is

flashing.

10. Continue to press “SET?” button until you

return to normal operating mode with a display similar to

the one shown here.

OPERATING MODES

The Digistat can be operated in one of three modes.

1) – Timed, all preset times and temperatures

2) – Continuous night temperature (useful for low limit temperature

protection when on holiday)

3) – Continuous ‘DAY 1’ temperature

Use the SELECT button to change the operating mode to suit your

requirements, the symbols are positioned on the right hand side of the display.

TEMPERATURE OVERRIDE

If at anytime during normal operation, you wish to temporarily increase or

decrease the set temperature use the + or – buttons to change to your desired

setting. This can be done without entering the SET mode five seconds after

releasing the + or – button the display will revert to showing the actual room

temperature. The Digistat will now control the temperature to the override

setting until the next programmed switching time, when it will revert to the

times and temperatures you have already programmed.

BATTERY REPLACEMENT

30 days before the batteries need replacing, a battery symbol

will flash in the right hand side of the display (Diagram C).

This signifies that four 1.5V type AA

alkaline batteries will

be needed to replace the existing ones. If battery replace-

ment is carried out in this condition the programmed

settings will only be held in the memory for a maximum of

1 minute, after which re-programming may be necessary.

YSTEM OFF SYSTEM ON

Diagram C

Continued overleaf

090-795 Digistat RF2 Inst IssB 12/5/06 16:13 Page 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Drayton Erie Digistat RF2 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info