Bedienungsanleitung Drayton MiTime T740M (Seite 1 von 2) (Englisch)

653176

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Step 1: Keys and Display - MiTime

RF Packs: T710R, T720R, T720M, T740R, T 740M

Single Channel: MiTime T710R Dual Channel: MiTime T720R, T720M Multi Channel: MiTime T740R, T740M

Step 2: Home Screens

→

What is a programmer?

... an explanation for householders

Programmers allow you to set ‘On’ and ‘Off’ time

periods. Some models switch the central heating and

domestic hot water on and off at the same time, while

others allow the domestic hot water and heating to

come on and go off at different times.

Set the ‘On’ and ‘Off’ time periods to suit your own

lifestyle. On some programmers you must also set

whether you want the heating and hot water to run

continuously, run under the chosen ‘On’ and ‘Off’

heating periods, or be permanently off.

The time on the programmer must be correct. Some

types have to be adjusted in spring and autumn at the

changes between Greenwich Mean Time and British

Summer Time.

You may be able to temporarily adjust the heating

programme, for example, ‘Override’, ‘Advance’ or

‘Boost’. These are explained in the manufacturer’s

instructions.

The heating will not work if the room thermostat has

switched the heating off. Also, if you have a hot-water

cylinder, the water heating

will not work if the cylinder

thermostat detects that the

hot water has reached the

correct temperature.

What is a room thermostat?

... an explanation for householders

A room thermostat simply switches the heating

system on and off as necessary. It works by sensing

the air temperature, switching on the heating when

the air temperature falls below the thermostat setting,

and switching it off once this set temperature has

been reached.

Turning a room thermostat to a higher setting will not

make the room heat up any faster. How quickly the

room heats up depends on the design of the heating

system, for example, the size of boiler and radiators.

Neither does the setting affect how quickly the room

cools down. Turning a room thermostat to a lower

setting will result in the room being controlled at a

lower temperature, and saves energy.

The heating system will not work if a time switch or

programmer has switched it off.

The way to set and use your room thermostat is to

ﬁnd the lowest temperature setting that you are

comfortable with, and then leave it alone to do its job.

The best way to do this is to set the room thermostat

to a low temperature – say 18ºC – and then turn it up

by one degree each day until you are comfortable

with the temperature. You won’t have to adjust the

thermostat further. Any adjustment above this setting

will waste energy and cost you more money.

If your heating system is a boiler with radiators, there

will usually be only one room thermostat to control the

whole house. But you can have different temperatures

in individual rooms by installing thermostatic radiator

valves (TRVs) on individual radiators. If you don’t

have TRVs, you should choose a temperature that is

reasonable for the whole house. If you do have TRVs,

you can choose a slightly higher setting to make sure

that even the coldest room is comfortable, then prevent

any overheating in other rooms by adjusting the TRVs.

Room thermostats need a free ﬂow of air to sense

the temperature, so they must not be covered by

curtains or blocked by furniture. Nearby electric

ﬁres, televisions, wall or table lamps may prevent the

thermostat from working properly.

What is a cylinder thermostat?

... an explanation for householders

A cylinder thermostat switches on and off the heat

supply from the boiler to the hot-water cylinder. It

works by sensing the temperature of the water inside

the cylinder, switching on the water heating when the

temperature falls below the thermostat setting, and

switching it off once this set temperature has been

reached.

Turning a cylinder thermostat to a higher setting will

not make the water heat up any faster. How quickly the

water heats up depends on the design of the heating

system, for example, the size of boiler and the heat

exchanger inside the cylinder.

The water heating will not work if a time switch or

programmer has switched it off. And the cylinder

thermostat will not always switch the boiler off,

because the boiler sometimes needs to heat the

radiators.

Cylinder thermostats are usually ﬁtted between one

quarter and one third of the way up the cylinder. The

cylinder thermostat will have a temperature scale

marked on it, and it should be set at between 60C and

65C, then left to do its job. This temperature is high

enough to kill off harmful bacteria in the water, but

raising the temperature of the stored hot water any

higher will result in wasted energy and increase the

risk of scalding.

If you have a boiler control thermostat, it should

always be set to a higher temperature than that of the

cylinder thermostat. In most boilers, a single boiler

thermostat controls the temperature of water sent

to both the cylinder and radiators, although in some

there are two separate boiler thermostats.

MiTime

MiStat

Drayton

MiTime

Programmer Series

RF Packs

Single Channel: MiTime T710R

Dual Channel: MiTime T720R, T720M

Multi Channel: MiTime T740R, T740M

Invensys

Customer Service Tel: 0845 130 5522

Customer Service Fax: 0845 130 0622

Technical Helpline: 0845 130 7722

Website: www.draytoncontrols.co.uk

E-mail: customer.care@invensys.com

@DraytonControls

/DraytonControls

EU Design Regs:- 002180638-1/2/3

User Guide 06490193001 Iss F

MiTime

MiStat

HOMEOWNER Guide

Zone = Heating

Current status: the programme is On

until 12:00 am

Link to zone details, see Step 3.

Link to Settings

See further details in Step 6.

Zone = Hot Water

Current status: the programme is

Off until 12:00 am

Link to zone details, see Step 3.

Press Select ( ) to view or edit zonePress Select ( ) to change mode Press Select ( ) to view or edit zone

Zone = Heating

Current status: the programme is On

until 12:00 am

Link to zone details, see Step 3.

Link to Settings

See further details in Step 6.

Zone = Hot Water

Current status: the programme is Off until

12:00 am. Link to zone details, see Step 3.

Zone = Zone 3

Current status: the programme is Always Off

Link to zone details, see Step 3.

HOMEOWNER Guide

Step 3: Zone Details

(not Single Channel)

→

Link to Settings

See further details in Step 6.

Now: describes the current status,

e.g. programme is On until 12:00 am.

Link to Programme timetable - see

further details in Step 4.

Temp: describes the current status

of the zone temperature, e.g.

Temperature in zone is 21.0C and the

setpoint is 21.5C

Link to modify the zone temperature.

Current mode: Auto

Options: see table in Step 3.

Temp: describes the current status of the

zone temperature, e.g. Temperature in

zone is 21.0C and the setpoint is 21.5C.

Link to modify the zone temperature.

Press Select ( ) to change mode

Link to Programme timetable

See further detail in Step 4.

MiTime

Home key: Press to go back

to the home screen at any

time

Date

Time

Back key: Press to return to

the previous screen

Help text to prompt for

next action. It relates to the

highlighted line

Arrow keys: Press to move

the highlight on screen, and

to change ﬁeld values

Advance key: Press from

the home or zone details

screens to advance to the

next on or off period

+hr key: Press from the

home or zone details

screens to add up to 3 hours

to the current period

Select key: Press to select highlighted

options, and to open and save editor screens

This icon used

throughout these

instructions refers

to this button

LED: Illuminates when any

zone is scheduled to be ON

Note:

See help in product menu for quick

button description.

: Indicates an RF transmission issue or

Service warning.

: Indicates that holiday is enabled

Home screen, depending on

model - see Step 2

Zone = Heating

Current mode: Auto

Options: see table below.

Now: describes the current status, e.g. programme

is On until 12:00 am. Link to Programme timetable

- see further details in Step 4.

Mode: Description:

Auto The programmer will control the

ON & OFF times in line with the

programmed timetable

Always Off The selected zone will be OFF

Always On The selected zone will be ON

All Day

(ﬁrst on / last

off)

The programme will control the

ON & OFF times in line with the

programmed timetable, but using

only the ﬁrst ON event and the last

OFF event - it will remain ON in

between these two periods.

Drayton MiTime T740M Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Drayton MiTime T740M

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info