Bedienungsanleitung Drayton RTS1 (Seite 1 von 2) (Englisch)

653187

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

RTS Thermostat

Installation instructions

Models

RTS1: Standard heating thermostat

RTS2 Heating thermostat with call for heat LED indicator

RTS3: Indoor frost thermostat

RTS4 Volt free heating/cooling change over switch

RTS9 & 10: Volt free heating/cooling changeover switch with call

for heating LED indicator

IMPORTANT NOTE

RTS thermostats are ELECTRONIC with a relay output.

Unless connected to a 230V mains supply the relay will

not operate, no 'click' will be heard and the call for heat

contact will remain open.

Location

Care should be taken to mount the thermostat in a position

which is not subject to direct sunlight or draughts. Preferably

it should be mounted on an inside wall about 1.5m (5ft)

above the floor in a position where it can respond to room

temperature but away from the direct influence of radiators

or other appliances giving off heat.

Note: If the thermostat is to be used as a frost protection

device it should be located in the coldest part of the premises.

Fixing

1. Loosen the securing screws, remove the wall-plate and, if

surface wiring is to be used, snap out the cable entry strip

on the bottom edge of the wall-plate with a pair of pliers.

2. Fix the wall-plate, terminals at the top, either direct onto a

flat wall using wall plugs and No 6 x 1” woodscrews or on a

flush mounting single conduit box using M 3.5 x 14 screws.

3. Complete the wiring to the wall-plate in accordance with

the relevant diagram shown overleaf in accordance with

I.E.E. regulations.

Note: The thermostat is for fixed wiring only and is double

insulated, the earthing continuity (loop) terminal is only

provided for convenience.

4. Plug the thermostat onto the wall-plate and tighten the

securing screws.

5. Before switching on the mains ENSURE THE CIRCUIT

FUSE IS 3A.

WARNING

Disconnect mains supply before fitting or removing from

wall-plate.

A switch having contact separation of at least 3mm in all

poles must be incorporated in the fixed wiring as a means

of providing full disconnection of the mains supply.

Setting

1. Set the desired room temperature on the control knob

against the setting mark.

2. The setting range may be limited or a particular setting

locked through the use of the mechanism to be found

under the control knob.

3. To adjust the limiters firstly set the thermostat to the

desired temperature and then carefully pull off the knob.

4. Lift and rotate the two limiting arms to re-position them in

the required notches.

5. Replace the knob with the previously set temperature

against the setting mark.

Technical data

Electrical supply: 230V ac 50Hz fused 3A

Double insulated (no earth required)

Temp. range: RTS1, 2, 4 & 9 10° to 30°C

RTS3 (Frost) 3° to 10°C

Switch type: RTS 1, 2 & 3 S.P.S.T 2(1)A 230V ac live

output

RTS4, 9 & 10 S.P.D.T 2(1)A 230V ac volt free

Temp. sensor: Electronic

RTS10

14° to 30°C

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Drayton RTS1 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info