Bedienungsanleitung DreamVision Eos (Seite 11 von 48) (Englisch)

768191

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

INSTALLATION GUIDELINES

R699900 - Eos Series User Manual 11

position.

Adjust the picture to your screen.

• The Vertical Shift level is between -80% and 80% of the Screen Height (0.80 x H).

• The Horizontal Shift level is between -34% and 34% of the Screen Base (0.34 x B).

• If the projector is not installed perpendicularly to the screen, use keystone correction to fulll your screen.

Note that using keystone correction, may be disabled by 3D projection. If you want the best possible 3D

pictures, It is not recommended to use trapezoidal correction.

• If you plan to use the vertical and horizontal shifts without keystone correction, make sure to not exceed the

values contained in the tab below for the Eos 1 and Eos 2:

Left / Right shift 0% 10% 20% 25% 30% 34%

max. up / down shift 80% 66% 47% 34% 18% 0%

• The Eos Signature has an extended shift range as follow:

Left / Right shift 0% 10% 20% 25% 30% 35% 43%

max. up / down shift 100% 87% 72% 58% 45% 22% 0%

•Adjust the picture position

The projector has motorized vertical and horizontal shifts. Browse into the Menu to the [Lens Control] setting

into the Installation menu, select the shift adjustment. Or use the direct access button on the Remote Control

Unit [Lens Control] to make the lens adjustment. You can use self-generated test pattern of the projector or an

external pattern, from a calibration DVD by example, by setting the Adjust pattern option to Off.

•Adjust the picture Zoom

Into the [Lens Control] menu, press the [Ok] button to access the Zoom adjustment. Use the up and down buttons

to adjust the picture size until the screen is completely lled.

•Adjust the Picture Focus

From the [Lens Control] menu, press the [Ok] button to access the Focus adjustment. Use the up and down

buttons to adjust the picture focus

Using Installation Modes

You can save the current picture position, zoom and focus into one of the 10 Installation Modes. Each Installation

Mode uses a memory that stores the current position, zoom, focus of the lens. Additionally, you can set a custom

name of 10 characters or less.

•Current lens setup

All the lens settings will be stored by default into the Installation Mode 1. You can also copy a Mode into another

using the Mode Copy function. Menu > Installation > Installation Mode > Mode Copy. Then you can call back

anytime later the current lens setup using the direct access button [Mode 1] up to [Mode 3] on the RCU.

•Limitations of use

Each memory can store a different picture size and position, but there are limitations on the possible pictures

sizes and positions because of the projector being at a xed location. In order to calculate the best position of the

projector toward the screen, the installer has to make sure that among the different desired pictures, the smaller

one with the smaller zoom, is within the offset limits (horizontal and vertical shifts) of the projector. Once the

position of the projector is determined by the smallest possible picture, double check that the larger one does not

exceed the zoom capacity.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DreamVision Eos Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info