768204
37
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
MISCELLANEOUS
R699860 - Siglos Plus User Manual 37
You want to... Command to send
Switch this unit Off send: 21h 89h 01h 50h 57h 30h 0Ah
receive: 06h 89h 01h 50h 57h 0Ah
Change active Input to HDMI2. send: 21h 89h 01h 49h 50h 37h 0Ah
or
send: 21h 89h 01h 52h 43h 37h 33h 37h 31h 0Ah
Change Gamma table to match HDR
video sources using EOTF curves
send: 21h 89h 01h 50h 4Dh 47h 54h 37h 0Ah
Change Lens Memory1 name to
“TV-size” (unused character are filled
with space = 20h)
send: 21h 89h 01h 49h 4Ch 4Dh 31h 0Ah
receive: 06h 89h 01h 49h 4Ch 4Dh 31h 0Ah
send: 54h 56h 2Dh 73h 69h 7Ah 65h 20h 20h 20h
receive: 06h 89h 01h 49h 4Ch 4Dh 31h 0Ah
17.2  LAN protocol
LAN / RJ-45 communication specification
The network settings may have to be modified in the projector’s network menu to match your current LAN network.
• DHCP Client: When set to ON, the projector’s IP address will be automatically set by the DHCP server. on the
LAN.
• IP Address: Sets the IP (Internet Protocol) address of the projector. A valid address must be set for this unit.
• Subnet Mask: Sets the Subnet Mask
• Default Gateway: Sets the Default IP Gateway of the projector.
• MAC Address: A 6 byte hex number that uniquely identifies the projector on the LAN. The value is unique to
each individual unit on the LAN network.
Sending a LAN Control Command
In order to send a Remote Control compatible command to this unit, you must open a TCP connection on port
20554. and send a command immediately as the connection will be dropped within 5 sec of inactivity. If for any
reason you have to change the TCP connection port, you may use the following RS-232c/LAN command.
[4Ch 53 50h 54h] + 4 ASCII chars as new port address in hexa
You want to set TCP port to 10000 Command to send
Send 10000 as new TCP port value:
10000 is 2710h in hexa, converted in
ASCII characters: 32h 37h 31h 30h
send: 21h 89h 01h 4Ch 53h 50h 54h 32h 37h 31h 30h 0Ah
receive: 06h 89h 01h 4Ch 53h 0Ah
Then, reboot Network module send: 21h 89h 01h 4Ch 53h 52h 53h 0Ah
receive: 06h 89h 01h 4Ch 53h 0Ah
Projector
2. Projector Ready
(PJ_OK)
4. Projector Acknowledge
(PJACK)
6. Projector confirms
`Control Device
1. Openning Connection
on port 20554
3. Command Type
(PJREQ)
5. Command
After 5sec,
connection is closed
37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für DreamVision Siglos plus wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info