Bedienungsanleitung DreamVision Siglos (Seite 10 von 44) (Englisch)

768195

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

R699850 - Siglos User Manual

INSTALLATION GUIDELINES

position

Adjust the picture to your screen.

• The Vertical Shift level is between -80% and 80% of the Screen Height (0.80 x H).

• The Horizontal Shift level is between -34% and 34% of the Screen Base (0.34 x B).

• If the projector is not installed perpendicularly to the screen, use keystone correction to fulll your screen.

Note that using keystone correction, may be disabled by 3D projection. If you want the best possible 3D

pictures, It is not recommended to use trapezoidal correction.

• If you plan to use the vertical and horizontal shifts without keystone correction, make sure to not exceed the

values contained in the tab below:

Left / Right shift 0% 5% 10% 15% 20% 25% 30% 34%

max. up / down shift 80% 74% 66% 57% 47% 34% 18% 0%

•Adjust the picture position

The Siglos projector has motorized vertical and horizontal shifts. Browse into the Menu to the [Lens Control]

setting into the Installation menu, select the shift adjustment. Or use the direct access button on the Remote

Control Unit [Lens Control] to make the lens adjustment. You can use self-generated test pattern of the projector

or an external pattern, from a calibration DVD by example, by setting the Adjust pattern option to Off.

•Adjust the picture Zoom

Into the [Lens Control] menu, press the [Ok] button to access the Zoom adjustment. Use the up and down buttons

to adjust the picture size until the screen is completely lled.

•Adjust the Picture Focus

From the [Lens Control] menu, press the [Ok] button to access the Focus adjustment. Use the up and down

buttons to adjust the picture focus

Using Lens Memories

You can save the current picture position, zoom and focus in up to 5 different Lens Memories (10 for Siglos 2&3).

Each memory stores the current position, zoom, focus of the lens and you can also set a custom name of 10

characters or less.

•Saving current lens setup

Fist step is to set the lens to ll the desired screen. Then go into the Menu > Installation > Lens Control, Select

Lens Memory Save and choose a free slot available. You can call back anytime later this current lens setup using

the direct access button [Lens Mem]ory on the RCU.

•Limitations of use

Each memory can store a different picture size and position, but there are limitations on the possible pictures

sizes and positions because of the projector being at a xed location. In order to calculate the best position of the

projector toward the screen, the installer has to make sure that among the different desired pictures, the smaller

one with the smaller zoom, is within the offset limits (horizontal and vertical shifts) of the projector. Once the

position of the projector is determined by the smallest possible picture, double check that the larger one does not

exceed the zoom capacity.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DreamVision Siglos Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info