Bedienungsanleitung DreamVision Star Light (Seite 34 von 48) (Englisch)

768201

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

8.0 MAINTENANCE

34 R699780 - Starlight User Manual

8.0 MAINTENANCE

8.1 Clean Dirt on the Cabinet

Always use a soft cloth. In case of heavy soiling, soak a cloth in neutral detergent diluted with water, wring dry and

wipe, followed by wiping again using a dry cloth.

Caution

Pay attention to the following as the cabinet may deteriorate in condition, get damaged or paint may come

off.

• Do not wipe with a stiff cloth.

• Do not wipe with force.

• Do not wipe with thinner or benzene.

• Do not spray volatile chemicals like insecticide.

• Do not allow prolonged contact with rubber or plastic products.

8.2 Dirt on the Lens

The lens shall be cleaned using commercial blowers or lens cleaning papers (for cleaning glasses and cameras).

Do not use ﬂuid-type cleaning agents. This may lead to peeling of the surface coating ﬁlm. The lens surface is

fragile. Avoid rubbing it hard or knocking.

8.3 Replacing the Lamp

Light-source Lamp and Lamp Usage Time

The life of light-source lamps used for this unit is about 3000 hours.

•The lamp life of 3000 hours is merely the average life span of light-source lamps and we do not provide any

guarantee for this ﬁgure. The lamp life may not reach 3000 hours depending on the operating conditions.

Deterioration progresses rapidly when the remaining lamp usage time is short. Get ready or replace with a new

lamp when the accumulated usage time exceeds 2900 hours. Depending on the operating conditions, the lamp

may have to be exchanged earlier.

If the image is dark or color tone abnormal, replace the lamp as soon as possible.

•You can also check the accumulated hours of usage. Please refer to Lamp Time in the Information menu.

When the lamp usage time reaches 2900 hours

The Lamp replacement message will be displayed on the screen the next three projection starts.

• Press the [BACK] button to clear the display.

Procedure for Lamp Replacement

During the lamp replacement process, you may have access to sensitive parts of the projector.

• Loosen the 2 screws on the lamp trap.

• Open the lamp Cover, at the rear of the projector.

• Loosen the 2 screws on the lamp unit to release it.

• Pull out the lamp unit using the handle.

• Insert the new lamp unit until it is ﬁrmly in place.

ABOUT LAMP REPLACEMENT

If this unit is installed in a constricted place, attempting to replace the lamp in that place may cause injury. Move this

unit to a place large enough to perform work.

Use only genuine replacement parts for the lamp unit. Otherwise, malfunction may occur. Also, never attempt to re-

use an old lamp unit. This may cause marked performance deterioration or lamp blowout, thus leading to unit

malfunction. Broken pieces of the lamp outside this unit may also cause injuries during lamp unit exchange.

Do not replace the lamp immediately after this unit has been used. The temperature of the lamp is still high and this

may cause a burn. Allow a cooling period of 1 hour or more before replacement.

Before replacing the lamp unit, pull out the power plug from the outlet and wait until the STANDBY/ON led is still light

red. Replacing a lamp with the plug connected to the outlet may cause injuries or electric shocks.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DreamVision Star Light Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info