Bedienungsanleitung Dremel 395T6 (Seite 2 von 92) (Englisch, Französisch, Spanisch)

25111

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Page 2

Power Tool Safety Rules

Read and understand all instructions. Failure to follow all instructions listed below, may

result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WARNING

Work Area

Keep your work area clean and well lit. Cluttered

benches and dark areas invite accidents.

Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases,

or dust. Power tools create sparks which may ignite the

dust or fumes.

Keep by-standers, children, and visitors away while

operating a power tool. Distractions can cause you to

lose control.

Electrical Safety

Double Insulated tools are equipped with a polarized

plug (one blade is wider than the other.) This plug

will fit in a polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse the plug. If it

still does not fit, contact a qualified electrician to

install a polarized outlet. Do not change the plug in

any way. Double Insulation eliminates the need for

the three wire grounded power cord and grounded

power supply system. Before plugging in the tool, be

certain the outlet voltage supplied is within the voltage

marked on the nameplate. Do not use “AC only” rated

tools with a DC power supply.

Avoid body contact with grounded surfaces such as

pipes, radiators, ranges and refrigerators. There is an

increased risk of electric shock if your body is

grounded. If operating the power tool in damp locations

is unavoidable, a Ground Fault Circuit Interrupter must

be used to supply the power to your tool. Electrician’s

rubber gloves and footwear will further enhance your

personal safety.

Don't expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

Do not abuse the cord. Never use the cord to carry the

tools or pull the plug from an outlet. Keep cord away

from heat, oil, sharp edges or moving parts. Replace

damaged cords immediately. Damaged cords increase

the risk of electric shock.

When operating a power tool outside, use an outdoor

extension cord marked "W-A" or "W." These cords are

rated for outdoor use and reduce the risk of electric

shock. Refer to “Recommended sizes of Extension

Cords” in the Accessory section of this manual.

Personal Safety

Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use tool

while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating

power tools may result in serious personal injury.

Dress properly. Do not wear loose clothing or jewelry.

Contain long hair. Keep your hair, clothing, and gloves

away from moving parts. Loose clothes, jewelry, or

long hair can be caught in moving parts. Keep handles

dry, clean and free from oil and grease.

Avoid accidental starting. Be sure switch is “OFF”

before plugging in. Carrying tools with your finger on

the switch or plugging in tools that have the switch

“ON” invites accidents.

Remove adjusting keys or wrenches before turning the

tool “ON”. A wrench or a key that is left attached to a

rotating part of the tool may result in personal injury.

Do not overreach. Keep proper footing and balance at

all times. Proper footing and balance enables better

control of the tool in unexpected situations.

Use safety equipment. Always wear eye protection.

Dust mask, non-skid safety shoes, hard hat, or hearing

protection must be used for appropriate conditions.

Tool Use and Care

Use clamps or other practical way to secure and

support the workpiece to a stable platform. Holding

the work by hand or against your body is unstable and

may lead to loss of control.

Do not force tool. Use the correct tool for your

application. The correct tool will do the job better and

safer at the rate for which it is designed.

Do not use tool if switch does not turn it “ON” or

“OFF”. Any tool that cannot be controlled with the

switch is dangerous and must be repaired.

Disconnect the plug from the power source before

making any adjustments, changing accessories, or

storing the tool. Such preventive safety measures

reduce the risk of starting the tool accidentally.

Store idle tools out of reach of children and other

untrained persons. Tools are dangerous in the hands of

untrained users.

Maintain tools with care. Keep cutting tools sharp and

clean. Properly maintained tools, with sharp cutting

edges are less likely to bind and are easier to control.

Any alteration or modification is a misuse and may

result in a dangerous condition.

Check for misalignment or binding of moving parts,

breakage of parts, and any other condition that may

affect the tools operation. If damaged, have the tool

serviced before using. Many accidents are caused by

poorly maintained tools. Develop a periodic

maintenance schedule for your tool.

DM 2610925474 10-04 10/19/04 3:39 PM Page 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dremel 395T6 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info