Bedienungsanleitung Dremel 395T6 (Seite 12 von 92) (Englisch, Französisch, Spanisch)

25111

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Page 12

Assembly & Operation of Attachments

Flex-Shaft 225

Not for use with router bits. Use

with router bits will cause

kickback.

INSTALLATION INSTRUCTIONS

It is extremely important to carefully read and follow

the directions to assemble the flex-shaft to your

rotary tool below to ensure the tool will function

properly

Attention: For optimum per

formance, allow your new

flex shaft attachment to run at high speed on your

rotary tool in a vertical position for 2 minutes before

use.

To properly attach the flex-shaft to the rotary tool,

THREE items must be removed from the tool: the

housing cap, collet nut and collet.

Step 1. Press the Shaft lock button, unscrew and

remove the collet nut.

If you need it, single-speed models also can have

speed control by using a Model 221 foot control unit.

Not for use with variable speed

or two speed models 285 or 395.

Use with external speed control will damage the

variable/two speed electronics.

The point to remember is this: You can do the great

majority of work with the single speed at its regular

speed of 35,000 RPM. But for certain materials and

types of work, you need slower speeds — which is the

reason the variable speed models and the speed

control units are available.

To aid you in determining the optimum operational

speed for different materials and different accessories,

we have constructed a series of tables that appear on

page 24, 25 and 26. By referring to these tables, you

can discover the recommended speeds for each type

of accessory. Look these tables over and become

familiar with them.

Ultimately, the best way to determine the correct speed

for work on any material is to practice for a few

minutes on a piece of scrap, even after referring to the

chart. You can quickly learn that a slower or faster

speed is more effective just by observing what happens

as you make a pass or two at different speeds. When

working with plastic, for example, start at a slow rate of

speed and increase the speed until you observe that the

plastic is melting at the point of contact. Then reduce

the speed slightly to get the optimum working speed.

Some rules of thumb in regard to speed:

1. Plastic and other materials that melt at low

temperatures should be cut at low speeds.

2. Polishing, buffing and cleaning with a wire brush

must be done at speeds not greater than 15,000

RPM to prevent damage to the brush.

3. Wood should be cut at high speed.

4. Iron or steel should be cut at high speed. If a high

speed steel cutter starts to chatter — this normally

means it is running too slow.

5. Aluminum, copper alloys, lead alloys, zinc alloys

and tin may be cut at various speeds, depending on

the type of cutting being done. Use paraffin or other

suitable lubricant on the cutter to prevent the cut

material from adhering to the cutter teeth.

Increasing the pressure on the tool is not the answer

when it is not performing as you think it should.

Perhaps you should be using a different accessory, and

perhaps an adjustment in speed would solve the

problem. Leaning on the tool does not help.

Let speed do the work!

Operating Speeds - (Cont.)

CAUTION

WARNING

STEP 1

DM 2610925474 10-04 10/19/04 3:40 PM Page 12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dremel 395T6 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info