Bedienungsanleitung Dremel 398 (Seite 3 von 76) (Französisch, Spanisch)

25121

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Page 3

Maintain tools with care. Keep cutting tools sharp

and clean. Properly maintained tools, with sharp

cutting edges are less likely to bind and are easier to

control. Any alteration or modification is a misuse and

may result in a dangerous condition.

Check for misalignment or binding of moving parts,

breakage of parts, and any other condition that may

affect the tools operation. If damaged, have the tool

serviced before using.

Many accidents are caused by

poorly maintained tools. Develop a periodic

maintenance schedule for your tool.

Use only accessories that are recommended by the

manufacturer for your model. Accessories that may

be suitable for one tool, may become hazardous when

used on another tool.

Service

Tool service must be performed only by qualified

repair personnel.

Service or maintenance performed

by unqualified personnel could result in a risk of

injury. For example: internal wires may be misplaced

or pinched, safety guard return springs may be

improperly mounted.

When servicing a tool, use only identical

replacement parts. Follow instructions in the

Maintenance section of this manual.

Use of

unauthorized parts or failure to follow Maintenance

Instructions may create a risk of electric shock or

injury. Certain cleaning agents such as gasoline,

carbon tetrachloride, ammonia, etc. may damage

plastic parts.

Safety Rules for Rotary Tools

Accessories must be rated for at least the speed

recommended on the tool warning label.

Wheels

and other accessories running over rated speed can

fly apart and cause injury.

Hold tool by insulated gripping surfaces when

performing an operation where the cutting tool may

contact hidden wiring or its own cord. Contact with

a "live" wire will make exposed metal parts of the tool

"live" and shock the operator. If cutting into existing

walls or other blind areas where electrical wiring may

exist is unavoidable, disconnect all fuses or circuit

breakers feeding this worksite.

Do not operate the flexible shaft with a sharp bend.

Over bending the shaft can generate excessive heat

on the jacket or hand piece. The recommended

minimum is 6" radius.

Always disconnect the power cord from the power

source before making any adjustments or attaching

any accessories. You may unexpectedly cause the

tool to start leading to serious personal injury.

Be aware of the switch location, when placing the

tool down or when picking the tool up. Y

ou may

accidentally activate the switch.

Always hold the hand piece firmly in your hands

during the start-up. The reaction torque of the motor,

as it accelerates to full speed, can cause the shaft to

twist.

Always wear safety goggles and dust mask. Use

only in well ventilated area.

Using personal safety

devices and working in safe environment reduces risk

of injury.

After changing the bits or making any adjustments,

make sure the collet nut and any other adjustment

devices are securely tightened. Loose adjustment

device can unexpectedly shift, causing loss of control,

loose rotating components will be violently thrown.

Do not reach in the area of the spinning bit. The

proximity of the spinning bit to your hand may not

always be obvious.

Allow brushes to run at operating speed for at least

one minute before using wheel. During this time no

one is to stand in front or in line with the brush.

Loose bristles or wires will be discharged during the

run-in time.

Wire and bristle brushes must never be operated at

speeds greater than 15,000/min. Direct the

discharge of the spinning wire brush away from

you. Small particles and tiny wire fragments may be

discharged at high velocity during the “cleaning”

action with these brushes and may become imbedded

in your skin. Bristles or wires will be discharged from

the brush at high speeds.

ear protective gloves and face shield with wire or

bristle brushes. Apply wire or bristle brushes lightly

to the work as only the tips of the wire/bristles do

the work. “Heavy” pressure on bristles will cause the

wire or bristle to become overstressed, resulting in a

wiping action and will cause the bristles/wire to be

discharged.

Carefully handle both the tool and individual

grinding wheels to avoid chipping or cracking.

Install a new wheel if tool is dropped while

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dremel 398 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info