Bedienungsanleitung Dremel 400seriesXPR (Seite 4 von 72) (Englisch, Französisch, Spanisch)

25125

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

SAFETY RULES FOR ROTARYTOOL(CONTINUED)

dropped while grinding. Do not use a

wheel that may be damaged.

Fragments

from a wheel that bursts during operation will

fly away at great velocity possibly striking you

or bystanders.

Never use dull or damaged bits. Sharp

bits must be handled with care.

Damaged

bits can snap during use. Dull bits require

more force to push the tool, possibly causing

the bit to break.

Use clamps to support workpiece when-

ever practical. Never hold a small work-

piece in one hand and the tool in the other

hand while in use. Allow for sufficient

space, at least 6", between your hand and

the spinning bit.

Round material such as

dowel rods, pipes or tubing have a tendency

to roll while being cut, and may cause the bit

to “bite” or jump toward you. Clamping a

small workpiece allows you to use both

hands to control the tool.

Inspect your workpiece before cutting.

When cutting irregularly shaped work-

pieces, plan your work so it will not slip

and pinch the bit and be torn from your

hand.

For example, if carving wood, make

sure there are no nails or foreign objects in

the workpiece. Nails or foreign objects can

cause the bit to jump.

Never start the tool when the bit is

engaged in the material.

The bit cutting

edge may grab the material causing loss of

control of the cutter.

Avoid bouncing and snagging the wheel,

especially when working corners, sharp

edges etc.

This can cause loss of control

and kick-back.

The direction of feed with the bit into the

material when carving, routing or cutting

is very important. Always feed the bit into

the material in the same direction as the

cutting edge is exiting from the material

(which is the same direction as the chips

are thrown).

Feeding the tool in the wrong

direction, causes the cutting edge of the bit to

climb out of the work and pull the tool in the

direction of this feed.

If the workpiece or bit becomes jammed

or bogged down, turn the tool “OFF” by

the switch. Wait for all moving parts to

stop and unplug the tool, then work to

free the jammed material.

If the switch to

the tool is left “ON” the tool could restart

unexpectedly causing serious personal

injury.

Do not leave a running tool unattended,

turn power off.

Only when tool comes to a

complete stop it is safe to put it down.

Do not grind or sand near flammable

materials.

Sparks from the wheel could

ignite these materials.

Do not touch the bit or collet after use.

After use the bit and collet are too hot to be

touched by bare hands.

Regularly clean the tool's air vents with

compressed air.

Excessive accumulation of

powdered metal inside the motor housing

may cause electrical failures.

Do not allow familiarity gained from fre-

quent use of your rotary tool to become

commonplace.

Always remember that a

careless fraction of a second is sufficient to

inflict severe injury.

Do not alter or misuse tool. Any alteration

or modification is a misuse and may result in

serious personal injury.

This product is not intended for use as a

dental drill, in human or veterinary med-

ical applications.

Serious injury may result.

When using the steel saws, cutoff wheels,

high speed cutters or tungsten carbide

cutters, always have the work securely

clamped. Never attempt to hold the work

with one hand while using any of these

accessories.

The reason is that these

wheels will grab if they become slightly cant-

ed in the groove, and can kickback causing

loss of control resulting in serious injury. Your

second hand should be used to steady and

guide the hand holding the tool. When a cut-

off wheel grabs, the wheel itself usually

breaks. When the steel saw, high speed cut-

ters or tungsten carbide cutter grab, it may

jump from the groove and you could lose

control of the tool.

Some dust created by

power drilling and other

construction activities, contains chemi-

cals known to cause cancer, birth defects

or other reproductive harm. Some exam-

ples of these chemicals are:

• Lead from lead-based paints,

• Crystalline silica from bricks and cement

and other masonry products, and

• Arsenic and chromium from chemically

treated lumber.

our risk from these exposures varies,

depending on how often you do this type of

work. To reduce your exposure to these

chemicals, work in a well ventilated area, and

work with approved safety equipment, such

as those dust masks that are specially

designed to filter out microscopic particles.

WARNING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dremel 400seriesXPR Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info