Bedienungsanleitung Dremel 8200 (Seite 20 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch, Norwegisch, Finnisch)

488595

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

these instructions to operate the power tool. Power tools

are dangerous in the hands of untrained users.

e . Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other

condition that may affect the power tools operation. If

damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

f . Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind

and are easier to control.

g . Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

BATTERY TOOL USE AND CARE

a . Recharge only with the charger speciﬁed by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of fire when used with

another battery pack.

b . Use power tools only with speciﬁcally designated

battery packs. Use of any other battery packs may create a

risk of injury and fire.

c . When battery pack is not in use, keep it away from

other metal objects like paper clips, coins, keys, nails,

screws, or other small metal objects that can make a

connection from one terminal to another. Shorting the

battery terminals together may cause burns or a fire.

d . Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,

ﬂush with water. If liquid contacts eyes, additionally

seek medical help. Liquid ejected from the battery may

cause irritation or burns.

SERVICE

a . Have your power tool serviced by a qualiﬁed repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR

ALLOPERATIONS

SAFETY WARNINGS COMMON FOR GRINDING,

SANDING, WIRE BRUSHING, POLISHING OR

ABRASIVE CUTTING-OFF OPERATIONS

a . This power tool is intended to function as a grinder,

sander, wire brush, polisher or cut-off tool. Read

all safety warnings, instructions, illustrations and

speciﬁcations provided with this power tool. Failure to

follow all instructions listed below may result in electric

shock, ﬁre and/or serious injury.

b . Do not use accessories which are not speciﬁcally

designed and recommended by the tool manufacturer.

Just because the accessory can be attached to your power

tool, it does not assure safe operation.

c . The rated speed of the accessory must be at least

equal to the maximum speed marked on the power tool.

Accessories running faster than their rated speed can break

and fly apart.

d . The outside diameter and the thickness of your

accessory must be within the capacity rating of your

power tool. Incorrectly sized accessories cannot be

adequately guarded or controlled.

e . The arbour size of wheels, ﬂanges, backing pads or

any other accessory must properly ﬁt the spindle of

the power tool. Accessories with arbour holes that do not

match the mounting hardware of the power tool will run

out of balance, vibrate excessively and may cause loss of

control.

f . Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for chips

and cracks, backing pad for cracks, tear or excess wear,

wire brush for loose or cracked wires. If power tool or

accessory is dropped, inspect for damage or install an

undamaged accessory. After inspecting and installing

anaccessory, position yourself and bystanders away

from the plane of the rotating accessory and run the

power tool at maximum no-load speed for one minute.

Damaged accessories will normally break apart during this

test time.

g . Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron capable of

stopping small abrasive or workpiece fragments. The

eye protection must be capable of stopping flying debris

generated by various operations. The dust mask or respirator

must be capable of filtrating particles generated by your

operation. Prolonged exposure to high intensity noise may

cause hearing loss.

h . Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal

protective equipment. Fragments of workpiece or of a

broken accessory may fly away and cause injury beyond

immediate area of operation.

i . Hold power tool by insulated gripping surfaces only,

when performing an operation where the cutting

accessory may contact hidden wiring or its own cord.

Cutting accessory contacting a "live" wire may make

exposed metal parts of the power tool "live" and shock the

operator.

j . Position the cord clear of the spinning accessory. If you

lose control, the cord may be cut or snagged and your hand

or arm may be pulled into the spinning accessory.

k . Never lay the power tool down until the accessory has

come to a complete stop. The spinning accessory may

grab the surface and pull the power tool out of your control.

l . Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could snag

your clothing, pulling the accessory into your body.

m . Regularly clean the power tool's air vents. The motor's

fan will draw the dust inside the housing and excessive

accumulation of powdered metal may cause electrical

hazards.

Dremel 8200 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info